ZoneMinder Forums

Hi All,

Is it possible to have web interface to set pre-set times for starting and stopping modect, has anyone been doing this with cron, if so how have you set this for /dev/video0(1) and the like

regards

fred

Hi

check chown and chgrp, chmod to user of zoneminder, this will be the same as /var/www/html/zm/events

ls -lh on this directory.

think you could ln the directory to your new location

regards

fred dodd

Hi All, first thanks for you help. here is my conf file for Mandrake 10 modules.conf probeall usb-interface usb-ohci above snd-trident snd-pcm-oss #ptions i2c-algo-bit bit_test=1 # card 45 = pico 2000 tuner = 0 options bttv card=1,45 tuner=0,0 gbuffers=4 options i2c-algo-bit bit_test=1 #options bttv ...

Hi All, first thanks for you help. here is my conf file for Mandrake 10 modules.conf probeall usb-interface usb-ohci above snd-trident snd-pcm-oss #ptions i2c-algo-bit bit_test=1 # card 45 = pico 2000 tuner = 0 options bttv card=1,45 tuner=0,0 gbuffers=4 options i2c-algo-bit bit_test=1 #options bttv ...

Hi all, If you use Source tab and select Device Format you have the option to set as 0=PAL 1=NTSC and I think 3 = Auto, I need to set my 2nd card Pico2000 to PAL-NC. Tried to pass this parameter in modules.conf with option bttv card=7 bttv_norm=3 # PAL-NC Has anyone got a Pico2000 working in colour ...

Hi Changed the file below and modules.conf with: options bttv card=1,7 javascript:emoticon(':)') vi modprobe.conf options bttv card=1,7 # change made alias eth0 8139too install snd-trident /sbin/modprobe --first-time --ignore-install snd-trident && { /sbin/modprobe snd-pcm-oss; /bin/true; } install ...

Hi All, Has anyone used mandrake 10 to load card type for two different cards. ie microPCTV card = 2 and another that i am trying to load as card = 7 output from dmesg bttv: driver version 0.9.12 loaded bttv: using 4 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0 ...

Hi,

Had this problem my self with an old motherboard, try at boot type ' livecd noscsi '
but it may be solved by trying out your own video card in an AGP or PCI slot.

How much RAM have you installed, its a must to have over 256mb and above.

let me know if you have any luck

regards

fred

Hi,

may I ask why are you installing these tools, are you setting the box as AP point, router!!

regards

fred

My colour camera is cctv 802c this would describe the product as below. They are working with gray setting but wish to produce colour from these cameras, tested with windoze and they do work.... I have tried setting RGB24 and used xawtv with command output. 'zmu -d <device_no> -q -v' to get a dump ...

Would like to add one more item with regards to install routine, would it be possible to able to set location in wizard for the images/ to a selected partition. another use would be partimage, use it for backing up systems this would be a good use /dev/hda1 none mount 30m with ram drive and kernel ...

had another problem with a new motherboard, the livecd would boot then video mode on VDU would go blank, tracked it down to the acpi in the bios, turned it off, it then moved on with the installation. the color maybe be due to how I set up the wires to the cctv cameras, they are in location and need ...

Hi My problem I encountered was due to some sdram that had a memory location fault, or that the kernel could not detect the correct amount of ram. In the system I was using 64mb 100mhz and 265 256 133mhz, used livecd mem=256M to pass to the kernel at boot, maybe a good use of f1 with tab key options ...