ZoneMinder Forums

Hi there, Just add a small add on to ZM; open zm_html.php add the line "include ("site_info.php"); sample of site_info.php could be the following; check the view type (where you may want the information be displayed.) <?php //check view type if ($view =="console" || $view=="login" || $view=="logout ...

Hi thee, I have a cctv card that said it supports 8-port real-tine capture; however, when i connect the cam with zoneminder, i use local mode (192.168.1.x/zm/) to view the page, the streaming is not smooth. I would like to know if there is any parameter I could config in module.conf to make sure the ...

Yes, I have for input available; Hi there, Thanks for the post; I have the same problem; the card saa7130 not able to detect correctly, so i try your method to reload the card until .. wow la.. the image displayed on the ZM screen... Thanks a lot .. i create a simple script to reload the drive as ...

Hi there, Thanks for the post; I have the same problem; the card saa7130 not able to detect correctly, so i try your method to reload the card until .. wow la.. the image displayed on the ZM screen... Thanks a lot .. i create a simple script to reload the drive as the following; hope it could help ...

Hi there, I have the saa7134 competible card installed. It used to work with Zoneminder; after I upgrade to FC5/ZM 1.2.3; the ZM only display grey color image. I would like to know how to add option to a module when it load to kernel. I try insmod saa7134 card=2, for example. but it seems did not ...

OK, here is what I did I use Ubuntu 5.05 and install the ZM with my SAA7134 card. it works. After I run the apt-get update/upgrade stuff. the system seems have some problem. I install the new system using ubuntu 6.0 and install ZM 1.2.3, after that it does not work any more; i even try to down-grade ...

I did not do anything, expect the ZM upgrade from 1.2.2 to 1.2.3 .. i really have no idea what went wrong;

cordel wrote:Are there in errors in the logs?
What did you do when you upgraded?

Regards,
Corey

Hi there, I have experience a strange problem. When I setup the ZoneMinder 1.2.2, my card works without problem. however, when I update to ZoneMinder 1.2.3; compile without problem; when i login to ZM, all I see is the grey box (the monitor) without image; I have double check the card (install in M ...

There, I finally change the CCTV Card and have it working under ubuntu 5.0.10.. The following is the new card's dmesg output ..It also show ' Huh, no eeprom present (err=-5)?' error, but it still works anway. Thanks anyone who try to help and read this post. ----- ACPI: PCI Interrupt 0000:02:06.0[A ...

Thanks for the suggestion, here is the output look like. it has a lot .. but it is pretty much same information.. 0000:02:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at ee10b000 (32-bit, prefetchable ...

Here with the dmesg dump .... I don't know what it means and hope it is useful for the expert to solve the problem... [4294736.222000] bttv2: using: *** UNKNOWN/GENERIC *** [card=0,autodetected] [4294736.222000] bttv2: gpio: en=00000000, out=00000000 in=00ffffff [init] [4294739.436000] tveeprom(bttv ...

I have a CCTV card installed on Ubuntu 5.0.x.

when I do 'dmesg|less' tt show the Card does not have EPROM with err=-5. I would like to know if the card is broken or it is a Window-software base CCTV card. If it is the later case, how can I make it work under Linux ..


BTW, the chip is SAA1730....