ZoneMinder Forums

are you ment to be running NTSC or something else?
i get the same when i fiirst set a box up because ZM always sets NTSC when i need PAL

also it may have to do with your modprobe.conf settings

yes the changes are shown via ipcs -l after the echo'ed changes i even edited the sysctl. file so the changes were set after a reboot. as said it seems no matter how much memory change is done , the result stays the same ie unable to set monitor res higher then 384x288 error below Jul 31 16:51:58 ...

well first off downloaded and installed ZMLinuxOS live. quick edit of modprobe.conf to set card to same has i had working under ZM 1.23.3 on suse 10.1, no big problems working stable and a nice low load on the system. Main problem is monitor size it will only run if i set size to 384x288 , why ...

just thought you would get a larger test base if a livecd was an option , as a lot of people wont have the linux skills to proform a compile and upgrade. i would myself but dont want to update my working system to 1.23.x ...just in case, so i'll await the feedback on the 1.23.x thread before i do ...

Is there a download any where for a LiveCD ver 1.23.x ?
cant seem to find one, or has it not gone LiveCD yet ?

It looks 99% like one i tried last week , seems to have a heat issue as it locks up or screws up the displayed video feed. You may have more luck than i did, but i should say i was (going to at a later date) going to fit some Heatsinks on the card chips and try and cool it down a tad. but at the ...

this might help you with your card

http://www.zoneminder.com/forums/viewtopic.php?t=5921

does anyone have any Pin out details on this Camera ?
GRUNDIG FAC 830


15 d plug for power and cam setup , but just need the power pins on this plug to try and fire the cam up for testing .

any info would be helpful as i belive the cam is working just cant test it

Thanks

you know if my brain was working today , i might have seen that !!!!
Thanks James

This may be posted in the wrong area.sorry I have a small problem , i installed a second capture card and added two new monitors /dev/video1(0) and /dev/video1(1) on the ZM console . how do i delete or remove them from the config to stop them showing up in the Montage. so i have 4 live monitors and ...

PLX PCI6150-BB66PC PLX Technology RSC#: 16585 Bridge: PCI-to-PCI PCI 6150 An asynchronous PCI-to-PCI bridge • 32-bit, 33/66 MHz asynchronous operation • 5V signal input tolerance and 5V signal to 3.3V signal conversions • 208-pin PQFP package • 1 KB FIFO size • PCI bus types • Transparent bridge fun ...

Connexant
Fusion 878A

this being the good part .

you should be able to use this card with no problem.
you may have to read a few posts regarding the 8 Cam setup but it's not to hard to do.
and you get plenty of help from the Forum Members.

JUMPtec Industrielle Computertechnik AG and Kontron Embedded Computers AG merged in July 2002. JUMPtec is now known as Kontron Embedded Modules GmbH. Products labeled and sold under the Kontron Embedded Modules name (formerly JUMPtec) are now considered Kontron products for all practical purposes ...

Sorry to inform you James but MMI has a point the setup for ZM4MS is not a easy setup for Newbies. i myself have still not got ZM4MS working and i have tried for the past 4 month to get it to work.which is a pity as it looks a good front end. and i have read the setup info and the posts made on ...

that setup is very close to mine (i have dual PIII x700) FPS is 1.5/1.7 running 4 CCD cams @ 640x480 load 1.3/3.4 does what i need but i think you might need more than the 1GB ram and most certain a larger HDD. PS also keep in mind the PSU for your Computer, upgrade to a good High output as the PCI ...