zmc crash ?????!!!!!

illo41100 · Post by **illo41100** » Tue Dec 13, 2005 8:07 pm

The Zmcd.log

Server starting at 05/12/13 20:58:07
'zmc -d /dev/video1' starting at 05/12/13 20:58:12, pid = 10849
'zmc -d /dev/video1' started at 05/12/13 20:58:12
'zmc -d /dev/video1' crashed at 05/12/13 20:58:12, exit status 210
'zmc -d /dev/video1' starting at 05/12/13 20:58:12, pid = 10852
'zmc -d /dev/video1' started at 05/12/13 20:58:12
'zmc -d /dev/video1' crashed at 05/12/13 20:58:12, exit status 210
Can't select: No child processes at /usr/local/bin/zmdc.pl line 593.
Server starting at 05/12/13 20:58:13
'zma -m 1' started at 05/12/13 20:58:16
'zma -m 1' starting at 05/12/13 20:58:16, pid = 10875
'zma -m 1' crashed at 05/12/13 20:58:16, exit status 210
'zma -m 1' started at 05/12/13 20:58:16
'zma -m 1' starting at 05/12/13 20:58:16, pid = 10877
'zma -m 1' crashed at 05/12/13 20:58:17, exit status 210
Can't select: No child processes at /usr/local/bin/zmdc.pl line 593.
Server starting at 05/12/13 20:58:18
'zmc -d /dev/video0/' starting at 05/12/13 20:58:21, pid = 10904
'zmc -d /dev/video0/' started at 05/12/13 20:58:21
'zmc -d /dev/video0/' crashed at 05/12/13 20:58:21, exit status 210
'zmc -d /dev/video0/' started at 05/12/13 20:58:21
'zmc -d /dev/video0/' starting at 05/12/13 20:58:21, pid = 10905
'zmc -d /dev/video0/' crashed at 05/12/13 20:58:21, exit status 210
Can't select: No child processes at /usr/local/bin/zmdc.pl line 593.
Server starting at 05/12/13 20:58:22
'zmfilter.pl' started at 05/12/13 20:58:25
'zmfilter.pl' starting at 05/12/13 20:58:25, pid = 10930
'zmaudit.pl -d 900 -y' starting at 05/12/13 20:58:34, pid = 10943
'zmaudit.pl -d 900 -y' started at 05/12/13 20:58:34
'zmwatch.pl' started at 05/12/13 20:58:36
'zmwatch.pl' starting at 05/12/13 20:58:36, pid = 10949
'zmwatch.pl ' stopping at 05/12/13 20:58:50
'zmwatch.pl ' died at 05/12/13 20:58:50, signal 14
'zmaudit.pl -d 900 -y' stopping at 05/12/13 20:58:50
'zmaudit.pl -d 900 -y' died at 05/12/13 20:58:50, signal 14
'zmfilter.pl ' stopping at 05/12/13 20:58:50
'zmfilter.pl ' died at 05/12/13 20:58:50, signal 14
Server shutdown at 05/12/13 20:59:00

Why this problem ?
With Xawtv , i view perfecly all 8 channel !

Post by **cordel** » Tue Dec 13, 2005 8:59 pm

I have a question.
On what distro?
What is the card config?
Is this zm from source or RPM?
What version?

Regards,
Corey

Post by **cordel** » Wed Dec 14, 2005 8:01 am

Did you figure out what you did wroNg ?
Should be /dev/video0
wide out the trailing /
Regards,
Corey

Post by **zoneminder** » Wed Dec 14, 2005 9:57 am

Also, /var/log/messages should give you some more information.

Phil

illo41100 · Post by **illo41100** » Fri Dec 16, 2005 6:49 pm

cordel wrote:I have a question.
On what distro?
What is the card config?
Is this zm from source or RPM?
What version?

Regards,
Corey

I have Suse 10
The capture cards is two UCC4 conexant chips 878a
The UCC4 have 4 composite channel input.
I have configured the bttv driver for 105 card ( Provideo PV143)
Provideo is equal as UCC4 card , IMHO

Zm is 1.21.4 from source.

The name of device is : /dev/video0 , /dev/video1 & working with xawtv
for all 8 composite channel. ( 4+4)

illo41100 · Post by **illo41100** » Fri Dec 16, 2005 6:50 pm

cordel wrote:Did you figure out what you did wroNg ?
Should be /dev/video0
wide out the trailing /
Regards,
Corey

With or without / the log not change !

jameswilson · Post by **jameswilson** » Fri Dec 16, 2005 6:52 pm

what resolution you trying to capture on what pallete

illo41100 · Post by **illo41100** » Fri Dec 16, 2005 7:01 pm

zoneminder wrote:Also, /var/log/messages should give you some more information.

Phil

Ok , what the log post ? apache ? boot ? error ? all ?

illo41100 · Post by **illo41100** » Fri Dec 16, 2005 7:07 pm

jameswilson wrote:what resolution you trying to capture on what pallete

various ..... 640*480 100*100 320*480 ecc , rgb grey ,yu , ecc ...i not view all channel.
The log report crash....

Post by **cordel** » Fri Dec 16, 2005 9:26 pm

zmc will crash if setting are that which the card don't support. If it works in xawtv then it will work in zm. The other thing to pay attention to is that the 878 chip don't like having different setting across its inputs, so all inputs on video0 should be the same size and pallet.

illo41100 · Post by **illo41100** » Sat Dec 17, 2005 5:01 pm

cordel wrote:zmc will crash if setting are that which the card don't support. If it works in xawtv then it will work in zm. The other thing to pay attention to is that the 878 chip don't like having different setting across its inputs, so all inputs on video0 should be the same size and pallet.

ok, the size & pallet for all input non change.

The problem persist

Zmc crash with a perl problem ? ( es: modules missing , old version , bad install perl , ecc ecc )

mudule perl-time-hires (downloaded, not present in suse 10 package)
the cause of this problem ?

illo41100 · Post by **illo41100** » Thu Dec 22, 2005 10:52 pm

any idea ?

Post by **cordel** » Fri Dec 23, 2005 7:13 am

Is there anything in your zmwatch.log?
How about if there is anything in your apache error_log or mysqld.log?
There is a better hint somewhere in the logs you just got to find where. Since several components are used for zm to work you need to check them all.

Regards,
Corey