I'm running on Ubuntu 8.04
I have 2 el-cheapo 4 port 878a cards single chips.
I need help with the options file .
I have tried many different drivers but can't seem to get both cards to work properly.
dmesg bottom half of the file>>
[ 29.803438] ACPI: Power Button (FF) [PWRF]
[ 29.803553] input: Power Button (CM) as /devices/virtual/input/input3
[ 29.819003] ACPI: Power Button (CM) [PWRB]
[ 29.819134] input: Sleep Button (CM) as /devices/virtual/input/input4
[ 29.830984] ACPI: Sleep Button (CM) [FUTS]
[ 30.066682] bttv: driver version 0.9.17 loaded
[ 30.066688] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 30.066781] bttv: Bt8xx card found (0).
[ 30.066813] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 18
[ 30.066829] bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 18, latency: 32, mmio: 0xe8002000
[ 30.066916] bttv0: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
[ 30.066951] bttv0: gpio: en=00000000, out=00000000 in=00f360ff [init]
[ 30.234796] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 30.565112] nvidia: module license 'NVIDIA' taints kernel.
[ 32.008163] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 32.909605] logips2pp: Detected unknown logitech mouse model 89
[ 33.382100] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input6
[ 33.398815] parport_pc 00:0a: reported by Plug and Play ACPI
[ 33.398938] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 33.516683] NET: Registered protocol family 10
[ 33.517052] lo: Disabled Privacy Extensions
[ 36.669702] bttv0: tuner absent
[ 36.672405] bttv0: registered device video0
[ 36.672456] bttv0: registered device vbi0
[ 36.672479] bttv0: PLL: 28636363 => 35468950 .. ok
[ 36.701778] bttv: Bt8xx card found (1).
[ 36.701818] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 36.701835] bttv1: Bt878 (rev 17) at 0000:00:0d.0, irq: 19, latency: 32, mmio: 0xe8004000
[ 36.701866] bttv1: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
[ 36.701904] bttv1: gpio: en=00000000, out=00000000 in=00f360ff [init]
[ 43.089245] bttv1: tuner absent
[ 43.089600] bttv1: registered device video1
[ 43.089809] bttv1: registered device vbi1
[ 43.089833] bttv1: PLL: 28636363 => 35468950 .. ok
[ 43.121236] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 43.121601] NVRM: loading NVIDIA Linux x86 Kernel Module 71.86.04 Mon Jan 21 11:22:18 PST 2008
[ 43.122480] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 21 (level, low) -> IRQ 21
[ 43.440558] intel8x0_measure_ac97_clock: measured 52368 usecs
[ 43.440564] intel8x0: clocking to 48000
[ 43.473507] bt878: AUDIO driver version 0.0.0 loaded
[ 43.473573] bt878: Bt878 AUDIO function found (0).
[ 43.473602] ACPI: PCI Interrupt 0000:00:09.1[A] -> GSI 17 (level, low) -> IRQ 18
[ 43.473612] bt878_probe: card id=[0x0], Unknown card.
[ 43.473614] Exiting..
[ 43.473620] ACPI: PCI interrupt for device 0000:00:09.1 disabled
[ 43.473630] bt878: probe of 0000:00:09.1 failed with error -22
[ 43.473639] bt878: Bt878 AUDIO function found (0).
[ 43.473659] ACPI: PCI Interrupt 0000:00:0d.1[A] -> GSI 19 (level, low) -> IRQ 19
[ 43.473666] bt878_probe: card id=[0x0], Unknown card.
[ 43.473668] Exiting..
[ 43.473673] ACPI: PCI interrupt for device 0000:00:0d.1 disabled
[ 43.473678] bt878: probe of 0000:00:0d.1 failed with error -22
[ 44.441427] lp0: using parport0 (interrupt-driven).
[ 44.462594] eth0: no IPv6 routers present
[ 44.525941] Adding 2265124k swap on /dev/sda5. Priority:-1 extents:1 across:2265124k
[ 45.103153] EXT3 FS on sda1, internal journal
[ 46.587371] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 47.240695] No dock devices found.
[ 50.683647] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 50.683656] apm: overridden by ACPI.
[ 56.804517] bttv0: PLL can sleep, using XTAL (28636363).
[ 58.014716] bttv1: PLL can sleep, using XTAL (28636363).
[ 64.847543] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 64.847982] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 64.848318] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 65.226416] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 65.226865] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 65.227244] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
Any tips
I have it set to options bttv card=77,77
Tried putting only 1 =77 but two lines and get similar results.
Thanks
Allan
2 bttv card options ???
forgot to mention
I have doubled the allocated memory.
Also
3 cams on 1 card and 2 on the other.
The card with 2 cams shows 3 separate images in the same window on the top 1/3 of this window.
1 cam on the other card did but no longer stays green in modect.it will not record at all.
Also
3 cams on 1 card and 2 on the other.
The card with 2 cams shows 3 separate images in the same window on the top 1/3 of this window.
1 cam on the other card did but no longer stays green in modect.it will not record at all.
hey found a link for your options, i noticed half way down in your dmesg tuners absent. hope it helps
http://www.zoneminder.com/forums/viewto ... onf+kodcon
http://www.zoneminder.com/forums/viewto ... onf+kodcon
it's improved
Thanks for the link I tried that driver code and added a ,77 after card=77 then the rest of the line.
The tuner absent part is still there but this card doesnt have a tv tuner. Looks just like the card in the pic's on the link above.
I still have a a couple of cams go fuzzy some times for no reason and then come back clear.
Below is the complete dmesg file after changing the driver.
dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.24-19-generic (buildd@terranova) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Fri Jul 11 23:41:49 UTC 2008 (Ubuntu 2.6.24-19.36-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
[ 0.000000] BIOS-e820: 000000005fff0000 - 000000005fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000005fff3000 - 0000000060000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 639MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f56c0
[ 0.000000] Entering add_active_range(0, 0, 393200) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 393200
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 393200
[ 0.000000] On node 0 totalpages: 393200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1279 pages used for memmap
[ 0.000000] HighMem zone: 162545 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F70C0 checksum 0
[ 0.000000] ACPI: RSDP 000F70C0, 0014 (r0 GBT )
[ 0.000000] ACPI: RSDT 5FFF3000, 002C (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: FACP 5FFF3040, 0074 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: DSDT 5FFF30C0, 3ADD (r1 GBT AWRDACPI 1000 MSFT 100000C)
[ 0.000000] ACPI: FACS 5FFF0000, 0040
[ 0.000000] ACPI: APIC 5FFF6BC0, 005A (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:2 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 70000000 (gap: 60000000:9ec00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 390129
[ 0.000000] Kernel command line: root=UUID=4200ef89-f3e1-4527-8a00-934f4fd8faad ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2019.909 MHz processor.
[ 13.090391] Console: colour VGA+ 80x25
[ 13.090396] console [tty0] enabled
[ 13.091119] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 13.091908] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 13.216439] Memory: 1546376k/1572800k available (2177k kernel code, 25144k reserved, 1006k data, 368k init, 655296k highmem)
[ 13.216455] virtual kernel memory layout:
[ 13.216456] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 13.216458] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 13.216459] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 13.216461] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 13.216462] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 13.216464] .data : 0xc0320474 - 0xc041bdc4 (1006 kB)
[ 13.216465] .text : 0xc0100000 - 0xc0320474 (2177 kB)
[ 13.216469] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 13.216546] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 13.296430] Calibrating delay using timer specific routine.. 4043.92 BogoMIPS (lpj=8087842)
[ 13.296476] Security Framework initialized
[ 13.296489] SELinux: Disabled at boot.
[ 13.296513] AppArmor: AppArmor initialized
[ 13.296520] Failure registering capabilities with primary security module.
[ 13.296533] Mount-cache hash table entries: 512
[ 13.296755] Initializing cgroup subsys ns
[ 13.296763] Initializing cgroup subsys cpuacct
[ 13.296781] CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 13.296800] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 13.296804] CPU: L2 cache: 512K
[ 13.296808] CPU: Hyper-Threading is disabled
[ 13.296812] CPU: After all inits, caps: 3febfbff 00000000 00000000 0000b080 00000000 00000000 00000000 00000000
[ 13.296831] Compat vDSO mapped to ffffe000.
[ 13.296853] Checking 'hlt' instruction... OK.
[ 13.312990] SMP alternatives: switching to UP code
[ 13.315235] Freeing SMP alternatives: 11k freed
[ 13.315420] Early unpacking initramfs... done
[ 13.789996] ACPI: Core revision 20070126
[ 13.790069] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 13.965652] CPU0: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
[ 13.965708] Total of 1 processors activated (4043.92 BogoMIPS).
[ 13.965823] ENABLING IO-APIC IRQs
[ 13.966008] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 14.111010] Brought up 1 CPUs
[ 14.111041] CPU0 attaching sched-domain:
[ 14.111045] domain 0: span 01
[ 14.111048] groups: 01
[ 14.111314] net_namespace: 64 bytes
[ 14.111323] Booting paravirtualized kernel on bare hardware
[ 14.112099] Time: 21:03:56 Date: 08/25/08
[ 14.112139] NET: Registered protocol family 16
[ 14.112445] EISA bus registered
[ 14.112475] ACPI: bus type pci registered
[ 14.155948] PCI: PCI BIOS revision 2.10 entry at 0xfad50, last bus=1
[ 14.155951] PCI: Using configuration type 1
[ 14.155957] Setting up standard PCI resources
[ 14.158574] ACPI: EC: Look up EC in DSDT
[ 14.162582] ACPI: Interpreter enabled
[ 14.162586] ACPI: (supports S0 S3 S4 S5)
[ 14.162607] ACPI: Using IOAPIC for interrupt routing
[ 14.168553] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 14.168822] Enabling SiS 96x SMBus.
[ 14.169868] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 14.192986] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 14.193123] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 14.193250] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 14.193380] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 14.193506] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 14.193632] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 14.193760] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 14.193884] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 14.194049] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 14.194098] pnp: PnP ACPI init
[ 14.194112] ACPI: bus type pnp registered
[ 14.198437] pnp: PnP ACPI: found 15 devices
[ 14.198441] ACPI: ACPI bus type pnp unregistered
[ 14.198448] PnPBIOS: Disabled by ACPI PNP
[ 14.198827] PCI: Using ACPI for IRQ routing
[ 14.198832] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 14.246709] NET: Registered protocol family 8
[ 14.246713] NET: Registered protocol family 20
[ 14.246815] AppArmor: AppArmor Filesystem Enabled
[ 14.250690] Time: tsc clocksource has been installed.
[ 14.258743] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 14.258747] system 00:02: ioport range 0x294-0x297 has been reserved
[ 14.289332] PCI: Bridge: 0000:00:01.0
[ 14.289336] IO window: disabled.
[ 14.289343] MEM window: e6000000-e7ffffff
[ 14.289349] PREFETCH window: e4000000-e5ffffff
[ 14.289381] NET: Registered protocol family 2
[ 14.326679] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 14.327163] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 14.328507] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 14.329340] TCP: Hash tables configured (established 131072 bind 65536)
[ 14.329346] TCP reno registered
[ 14.338797] checking if image is initramfs... it is
[ 14.789714] Switched to high resolution mode on CPU 0
[ 15.273176] Freeing initrd memory: 7906k freed
[ 15.274008] audit: initializing netlink socket (disabled)
[ 15.274031] audit(1219698236.788:1): initialized
[ 15.274337] highmem bounce pool size: 64 pages
[ 15.277234] VFS: Disk quotas dquot_6.5.1
[ 15.277351] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 15.277572] io scheduler noop registered
[ 15.277575] io scheduler anticipatory registered
[ 15.277578] io scheduler deadline registered
[ 15.277597] io scheduler cfq registered (default)
[ 15.277656] Boot video device is 0000:01:00.0
[ 15.278046] isapnp: Scanning for PnP cards...
[ 15.631531] isapnp: No Plug & Play device found
[ 15.674706] Real Time Clock Driver v1.12ac
[ 15.674853] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 15.675005] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 15.675190] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 15.676553] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 15.677088] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 15.678352] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 15.678452] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 15.678619] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 15.678961] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 15.678968] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 15.688041] mice: PS/2 mouse device common for all mice
[ 15.688221] EISA: Probing bus 0 at eisa.0
[ 15.688231] Cannot allocate resource for EISA slot 1
[ 15.688263] EISA: Detected 0 cards.
[ 15.688268] cpuidle: using governor ladder
[ 15.688271] cpuidle: using governor menu
[ 15.688410] NET: Registered protocol family 1
[ 15.688456] Using IPI No-Shortcut mode
[ 15.688502] registered taskstats version 1
[ 15.688619] Magic number: 4:632:96
[ 15.688781] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 15.688784] EDD information not available.
[ 15.689264] Freeing unused kernel memory: 368k freed
[ 15.719906] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 17.035691] fuse init (API version 7.9)
[ 17.100538] device-mapper: uevent: version 1.0.3
[ 17.100611] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
[ 18.003546] usbcore: registered new interface driver usbfs
[ 18.003584] usbcore: registered new interface driver hub
[ 18.027417] usbcore: registered new device driver usb
[ 18.036444] SCSI subsystem initialized
[ 18.104741] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.104827] ACPI: PCI Interrupt 0000:00:02.2[D] -> GSI 20 (level, low) -> IRQ 16
[ 18.104849] ohci_hcd 0000:00:02.2: OHCI Host Controller
[ 18.105297] ohci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[ 18.105323] ohci_hcd 0000:00:02.2: irq 16, io mem 0xe8000000
[ 18.151137] libata version 3.00 loaded.
[ 18.161312] usb usb1: configuration #1 chosen from 1 choice
[ 18.161352] hub 1-0:1.0: USB hub found
[ 18.161364] hub 1-0:1.0: 3 ports detected
[ 18.162122] 8139too Fast Ethernet driver 0.9.28
[ 18.263068] ACPI: PCI Interrupt 0000:00:02.3[A] -> GSI 23 (level, low) -> IRQ 17
[ 18.263092] ohci_hcd 0000:00:02.3: OHCI Host Controller
[ 18.263130] ohci_hcd 0000:00:02.3: new USB bus registered, assigned bus number 2
[ 18.263153] ohci_hcd 0000:00:02.3: irq 17, io mem 0xe8001000
[ 18.279074] Floppy drive(s): fd0 is 1.44M
[ 18.298675] FDC 0 is a post-1991 82077
[ 18.320980] usb usb2: configuration #1 chosen from 1 choice
[ 18.321023] hub 2-0:1.0: USB hub found
[ 18.321035] hub 2-0:1.0: 3 ports detected
[ 18.422968] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 17 (level, low) -> IRQ 18
[ 18.423753] eth0: RealTek RTL8139 at 0xe800, 00:20:ed:3e:c7:a5, IRQ 18
[ 18.423757] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 18.432807] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 18.439024] pata_sis 0000:00:02.5: version 0.5.2
[ 18.441505] scsi0 : pata_sis
[ 18.442953] scsi1 : pata_sis
[ 18.443885] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 18.443889] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 18.648835] ata1.00: ATA-7: ST3160815A, 3.AAD, max UDMA/100
[ 18.648841] ata1.00: 312581808 sectors, multi 16: LBA48
[ 18.715268] ata1.00: configured for UDMA/100
[ 19.357292] ata2.00: ATAPI: JLMS XJ-HD166S, DTS5, max UDMA/33
[ 19.357326] ata2.01: ATAPI: LITE-ON LTR-48327S, PTS1, max UDMA/33
[ 19.512855] ata2.00: configured for UDMA/33
[ 19.684411] ata2.01: configured for UDMA/33
[ 19.684596] scsi 0:0:0:0: Direct-Access ATA ST3160815A 3.AA PQ: 0 ANSI: 5
[ 19.685416] scsi 1:0:0:0: CD-ROM JLMS XJ-HD166S DTS5 PQ: 0 ANSI: 5
[ 19.686415] scsi 1:0:1:0: CD-ROM LITE-ON LTR-48327S PTS1 PQ: 0 ANSI: 5
[ 19.708215] Driver 'sd' needs updating - please use bus_type methods
[ 19.708352] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 19.708373] sd 0:0:0:0: [sda] Write Protect is off
[ 19.708377] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 19.708406] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 19.708481] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 19.708497] sd 0:0:0:0: [sda] Write Protect is off
[ 19.708501] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 19.708528] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 19.708534] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 19.726306] sda1 sda2 <sda5>
[ 19.752870] sd 0:0:0:0: [sda] Attached SCSI disk
[ 19.762189] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 19.762197] Uniform CD-ROM driver Revision: 3.20
[ 19.762276] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 19.763510] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 19.763540] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 19.763567] sr 1:0:1:0: Attached scsi generic sg2 type 5
[ 19.767481] sr1: scsi3-mmc drive: 197x/48x writer cd/rw xa/form2 cdda tray
[ 19.767578] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 20.226879] Attempting manual resume
[ 20.226885] swsusp: Resume From Partition 8:5
[ 20.226888] PM: Checking swsusp image.
[ 20.227146] PM: Resume from disk failed.
[ 20.288112] kjournald starting. Commit interval 5 seconds
[ 20.288130] EXT3-fs: mounted filesystem with ordered data mode.
[ 28.862612] Linux agpgart interface v0.102
[ 28.914111] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 29.130899] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 29.189802] agpgart: Detected SiS chipset - id:1616
[ 29.194445] agpgart: AGP aperture is 64M @ 0xe0000000
[ 29.374265] Linux video capture interface: v2.00
[ 29.684865] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x1400
[ 29.749069] input: Power Button (FF) as /devices/virtual/input/input2
[ 29.760594] ACPI: Power Button (FF) [PWRF]
[ 29.760780] input: Power Button (CM) as /devices/virtual/input/input3
[ 29.776571] ACPI: Power Button (CM) [PWRB]
[ 29.776726] input: Sleep Button (CM) as /devices/virtual/input/input4
[ 29.792539] ACPI: Sleep Button (CM) [FUTS]
[ 30.137205] bttv: driver version 0.9.17 loaded
[ 30.137211] bttv: using 32 buffers with 2080k (520 pages) each for capture
[ 30.137306] bttv: Bt8xx card found (0).
[ 30.137338] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 18
[ 30.137355] bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 18, latency: 32, mmio: 0xe8002000
[ 30.137442] bttv0: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
[ 30.137478] bttv0: gpio: en=00000000, out=00000000 in=00f360ff [init]
[ 30.223382] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 30.664401] logips2pp: Detected unknown logitech mouse model 89
[ 30.822842] nvidia: module license 'NVIDIA' taints kernel.
[ 31.136228] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input6
[ 31.226959] parport_pc 00:0a: reported by Plug and Play ACPI
[ 31.227075] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 32.427717] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 33.506411] NET: Registered protocol family 10
[ 33.506780] lo: Disabled Privacy Extensions
[ 36.620341] bttv0: tuner absent
[ 36.620454] bttv0: registered device video0
[ 36.620503] bttv0: registered device vbi0
[ 36.620525] bttv0: PLL: 28636363 => 35468950 .. ok
[ 36.651247] bttv: Bt8xx card found (1).
[ 36.651285] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 36.651302] bttv1: Bt878 (rev 17) at 0000:00:0d.0, irq: 19, latency: 32, mmio: 0xe8004000
[ 36.651337] bttv1: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
[ 36.651373] bttv1: gpio: en=00000000, out=00000000 in=00f360ff [init]
[ 43.050768] bttv1: tuner absent
[ 43.051136] bttv1: registered device video1
[ 43.051361] bttv1: registered device vbi1
[ 43.051383] bttv1: PLL: 28636363 => 35468950 .. ok
[ 43.082757] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 43.083107] NVRM: loading NVIDIA Linux x86 Kernel Module 71.86.04 Mon Jan 21 11:22:18 PST 2008
[ 43.084232] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 21 (level, low) -> IRQ 21
[ 43.402083] intel8x0_measure_ac97_clock: measured 52387 usecs
[ 43.402089] intel8x0: clocking to 48000
[ 43.484680] bt878: AUDIO driver version 0.0.0 loaded
[ 43.484746] bt878: Bt878 AUDIO function found (0).
[ 43.484788] ACPI: PCI Interrupt 0000:00:09.1[A] -> GSI 17 (level, low) -> IRQ 18
[ 43.484798] bt878_probe: card id=[0x0], Unknown card.
[ 43.484800] Exiting..
[ 43.484806] ACPI: PCI interrupt for device 0000:00:09.1 disabled
[ 43.484816] bt878: probe of 0000:00:09.1 failed with error -22
[ 43.484825] bt878: Bt878 AUDIO function found (0).
[ 43.484844] ACPI: PCI Interrupt 0000:00:0d.1[A] -> GSI 19 (level, low) -> IRQ 19
[ 43.484852] bt878_probe: card id=[0x0], Unknown card.
[ 43.484853] Exiting..
[ 43.484859] ACPI: PCI interrupt for device 0000:00:0d.1 disabled
[ 43.484864] bt878: probe of 0000:00:0d.1 failed with error -22
[ 43.637622] eth0: no IPv6 routers present
[ 44.454537] lp0: using parport0 (interrupt-driven).
[ 44.539191] Adding 2265124k swap on /dev/sda5. Priority:-1 extents:1 across:2265124k
[ 45.116142] EXT3 FS on sda1, internal journal
[ 46.608876] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 47.270543] No dock devices found.
[ 50.679834] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 50.679842] apm: overridden by ACPI.
[ 56.876207] bttv0: PLL can sleep, using XTAL (28636363).
[ 58.089510] bttv1: PLL can sleep, using XTAL (28636363).
[ 65.325603] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 65.326050] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 65.326384] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 65.778165] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 65.778677] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 65.779017] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
The tuner absent part is still there but this card doesnt have a tv tuner. Looks just like the card in the pic's on the link above.
I still have a a couple of cams go fuzzy some times for no reason and then come back clear.
Below is the complete dmesg file after changing the driver.
dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.24-19-generic (buildd@terranova) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Fri Jul 11 23:41:49 UTC 2008 (Ubuntu 2.6.24-19.36-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
[ 0.000000] BIOS-e820: 000000005fff0000 - 000000005fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000005fff3000 - 0000000060000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 639MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f56c0
[ 0.000000] Entering add_active_range(0, 0, 393200) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 393200
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 393200
[ 0.000000] On node 0 totalpages: 393200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1279 pages used for memmap
[ 0.000000] HighMem zone: 162545 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F70C0 checksum 0
[ 0.000000] ACPI: RSDP 000F70C0, 0014 (r0 GBT )
[ 0.000000] ACPI: RSDT 5FFF3000, 002C (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: FACP 5FFF3040, 0074 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: DSDT 5FFF30C0, 3ADD (r1 GBT AWRDACPI 1000 MSFT 100000C)
[ 0.000000] ACPI: FACS 5FFF0000, 0040
[ 0.000000] ACPI: APIC 5FFF6BC0, 005A (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:2 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 70000000 (gap: 60000000:9ec00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 390129
[ 0.000000] Kernel command line: root=UUID=4200ef89-f3e1-4527-8a00-934f4fd8faad ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2019.909 MHz processor.
[ 13.090391] Console: colour VGA+ 80x25
[ 13.090396] console [tty0] enabled
[ 13.091119] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 13.091908] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 13.216439] Memory: 1546376k/1572800k available (2177k kernel code, 25144k reserved, 1006k data, 368k init, 655296k highmem)
[ 13.216455] virtual kernel memory layout:
[ 13.216456] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 13.216458] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 13.216459] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 13.216461] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 13.216462] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 13.216464] .data : 0xc0320474 - 0xc041bdc4 (1006 kB)
[ 13.216465] .text : 0xc0100000 - 0xc0320474 (2177 kB)
[ 13.216469] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 13.216546] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 13.296430] Calibrating delay using timer specific routine.. 4043.92 BogoMIPS (lpj=8087842)
[ 13.296476] Security Framework initialized
[ 13.296489] SELinux: Disabled at boot.
[ 13.296513] AppArmor: AppArmor initialized
[ 13.296520] Failure registering capabilities with primary security module.
[ 13.296533] Mount-cache hash table entries: 512
[ 13.296755] Initializing cgroup subsys ns
[ 13.296763] Initializing cgroup subsys cpuacct
[ 13.296781] CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 13.296800] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 13.296804] CPU: L2 cache: 512K
[ 13.296808] CPU: Hyper-Threading is disabled
[ 13.296812] CPU: After all inits, caps: 3febfbff 00000000 00000000 0000b080 00000000 00000000 00000000 00000000
[ 13.296831] Compat vDSO mapped to ffffe000.
[ 13.296853] Checking 'hlt' instruction... OK.
[ 13.312990] SMP alternatives: switching to UP code
[ 13.315235] Freeing SMP alternatives: 11k freed
[ 13.315420] Early unpacking initramfs... done
[ 13.789996] ACPI: Core revision 20070126
[ 13.790069] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 13.965652] CPU0: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
[ 13.965708] Total of 1 processors activated (4043.92 BogoMIPS).
[ 13.965823] ENABLING IO-APIC IRQs
[ 13.966008] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 14.111010] Brought up 1 CPUs
[ 14.111041] CPU0 attaching sched-domain:
[ 14.111045] domain 0: span 01
[ 14.111048] groups: 01
[ 14.111314] net_namespace: 64 bytes
[ 14.111323] Booting paravirtualized kernel on bare hardware
[ 14.112099] Time: 21:03:56 Date: 08/25/08
[ 14.112139] NET: Registered protocol family 16
[ 14.112445] EISA bus registered
[ 14.112475] ACPI: bus type pci registered
[ 14.155948] PCI: PCI BIOS revision 2.10 entry at 0xfad50, last bus=1
[ 14.155951] PCI: Using configuration type 1
[ 14.155957] Setting up standard PCI resources
[ 14.158574] ACPI: EC: Look up EC in DSDT
[ 14.162582] ACPI: Interpreter enabled
[ 14.162586] ACPI: (supports S0 S3 S4 S5)
[ 14.162607] ACPI: Using IOAPIC for interrupt routing
[ 14.168553] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 14.168822] Enabling SiS 96x SMBus.
[ 14.169868] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 14.192986] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 14.193123] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 14.193250] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 14.193380] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 14.193506] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 14.193632] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 14.193760] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 14.193884] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 14.194049] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 14.194098] pnp: PnP ACPI init
[ 14.194112] ACPI: bus type pnp registered
[ 14.198437] pnp: PnP ACPI: found 15 devices
[ 14.198441] ACPI: ACPI bus type pnp unregistered
[ 14.198448] PnPBIOS: Disabled by ACPI PNP
[ 14.198827] PCI: Using ACPI for IRQ routing
[ 14.198832] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 14.246709] NET: Registered protocol family 8
[ 14.246713] NET: Registered protocol family 20
[ 14.246815] AppArmor: AppArmor Filesystem Enabled
[ 14.250690] Time: tsc clocksource has been installed.
[ 14.258743] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 14.258747] system 00:02: ioport range 0x294-0x297 has been reserved
[ 14.289332] PCI: Bridge: 0000:00:01.0
[ 14.289336] IO window: disabled.
[ 14.289343] MEM window: e6000000-e7ffffff
[ 14.289349] PREFETCH window: e4000000-e5ffffff
[ 14.289381] NET: Registered protocol family 2
[ 14.326679] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 14.327163] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 14.328507] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 14.329340] TCP: Hash tables configured (established 131072 bind 65536)
[ 14.329346] TCP reno registered
[ 14.338797] checking if image is initramfs... it is
[ 14.789714] Switched to high resolution mode on CPU 0
[ 15.273176] Freeing initrd memory: 7906k freed
[ 15.274008] audit: initializing netlink socket (disabled)
[ 15.274031] audit(1219698236.788:1): initialized
[ 15.274337] highmem bounce pool size: 64 pages
[ 15.277234] VFS: Disk quotas dquot_6.5.1
[ 15.277351] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 15.277572] io scheduler noop registered
[ 15.277575] io scheduler anticipatory registered
[ 15.277578] io scheduler deadline registered
[ 15.277597] io scheduler cfq registered (default)
[ 15.277656] Boot video device is 0000:01:00.0
[ 15.278046] isapnp: Scanning for PnP cards...
[ 15.631531] isapnp: No Plug & Play device found
[ 15.674706] Real Time Clock Driver v1.12ac
[ 15.674853] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 15.675005] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 15.675190] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 15.676553] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 15.677088] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 15.678352] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 15.678452] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 15.678619] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 15.678961] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 15.678968] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 15.688041] mice: PS/2 mouse device common for all mice
[ 15.688221] EISA: Probing bus 0 at eisa.0
[ 15.688231] Cannot allocate resource for EISA slot 1
[ 15.688263] EISA: Detected 0 cards.
[ 15.688268] cpuidle: using governor ladder
[ 15.688271] cpuidle: using governor menu
[ 15.688410] NET: Registered protocol family 1
[ 15.688456] Using IPI No-Shortcut mode
[ 15.688502] registered taskstats version 1
[ 15.688619] Magic number: 4:632:96
[ 15.688781] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 15.688784] EDD information not available.
[ 15.689264] Freeing unused kernel memory: 368k freed
[ 15.719906] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 17.035691] fuse init (API version 7.9)
[ 17.100538] device-mapper: uevent: version 1.0.3
[ 17.100611] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
[ 18.003546] usbcore: registered new interface driver usbfs
[ 18.003584] usbcore: registered new interface driver hub
[ 18.027417] usbcore: registered new device driver usb
[ 18.036444] SCSI subsystem initialized
[ 18.104741] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.104827] ACPI: PCI Interrupt 0000:00:02.2[D] -> GSI 20 (level, low) -> IRQ 16
[ 18.104849] ohci_hcd 0000:00:02.2: OHCI Host Controller
[ 18.105297] ohci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[ 18.105323] ohci_hcd 0000:00:02.2: irq 16, io mem 0xe8000000
[ 18.151137] libata version 3.00 loaded.
[ 18.161312] usb usb1: configuration #1 chosen from 1 choice
[ 18.161352] hub 1-0:1.0: USB hub found
[ 18.161364] hub 1-0:1.0: 3 ports detected
[ 18.162122] 8139too Fast Ethernet driver 0.9.28
[ 18.263068] ACPI: PCI Interrupt 0000:00:02.3[A] -> GSI 23 (level, low) -> IRQ 17
[ 18.263092] ohci_hcd 0000:00:02.3: OHCI Host Controller
[ 18.263130] ohci_hcd 0000:00:02.3: new USB bus registered, assigned bus number 2
[ 18.263153] ohci_hcd 0000:00:02.3: irq 17, io mem 0xe8001000
[ 18.279074] Floppy drive(s): fd0 is 1.44M
[ 18.298675] FDC 0 is a post-1991 82077
[ 18.320980] usb usb2: configuration #1 chosen from 1 choice
[ 18.321023] hub 2-0:1.0: USB hub found
[ 18.321035] hub 2-0:1.0: 3 ports detected
[ 18.422968] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 17 (level, low) -> IRQ 18
[ 18.423753] eth0: RealTek RTL8139 at 0xe800, 00:20:ed:3e:c7:a5, IRQ 18
[ 18.423757] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 18.432807] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 18.439024] pata_sis 0000:00:02.5: version 0.5.2
[ 18.441505] scsi0 : pata_sis
[ 18.442953] scsi1 : pata_sis
[ 18.443885] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 18.443889] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 18.648835] ata1.00: ATA-7: ST3160815A, 3.AAD, max UDMA/100
[ 18.648841] ata1.00: 312581808 sectors, multi 16: LBA48
[ 18.715268] ata1.00: configured for UDMA/100
[ 19.357292] ata2.00: ATAPI: JLMS XJ-HD166S, DTS5, max UDMA/33
[ 19.357326] ata2.01: ATAPI: LITE-ON LTR-48327S, PTS1, max UDMA/33
[ 19.512855] ata2.00: configured for UDMA/33
[ 19.684411] ata2.01: configured for UDMA/33
[ 19.684596] scsi 0:0:0:0: Direct-Access ATA ST3160815A 3.AA PQ: 0 ANSI: 5
[ 19.685416] scsi 1:0:0:0: CD-ROM JLMS XJ-HD166S DTS5 PQ: 0 ANSI: 5
[ 19.686415] scsi 1:0:1:0: CD-ROM LITE-ON LTR-48327S PTS1 PQ: 0 ANSI: 5
[ 19.708215] Driver 'sd' needs updating - please use bus_type methods
[ 19.708352] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 19.708373] sd 0:0:0:0: [sda] Write Protect is off
[ 19.708377] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 19.708406] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 19.708481] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 19.708497] sd 0:0:0:0: [sda] Write Protect is off
[ 19.708501] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 19.708528] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 19.708534] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 19.726306] sda1 sda2 <sda5>
[ 19.752870] sd 0:0:0:0: [sda] Attached SCSI disk
[ 19.762189] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 19.762197] Uniform CD-ROM driver Revision: 3.20
[ 19.762276] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 19.763510] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 19.763540] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 19.763567] sr 1:0:1:0: Attached scsi generic sg2 type 5
[ 19.767481] sr1: scsi3-mmc drive: 197x/48x writer cd/rw xa/form2 cdda tray
[ 19.767578] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 20.226879] Attempting manual resume
[ 20.226885] swsusp: Resume From Partition 8:5
[ 20.226888] PM: Checking swsusp image.
[ 20.227146] PM: Resume from disk failed.
[ 20.288112] kjournald starting. Commit interval 5 seconds
[ 20.288130] EXT3-fs: mounted filesystem with ordered data mode.
[ 28.862612] Linux agpgart interface v0.102
[ 28.914111] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 29.130899] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 29.189802] agpgart: Detected SiS chipset - id:1616
[ 29.194445] agpgart: AGP aperture is 64M @ 0xe0000000
[ 29.374265] Linux video capture interface: v2.00
[ 29.684865] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x1400
[ 29.749069] input: Power Button (FF) as /devices/virtual/input/input2
[ 29.760594] ACPI: Power Button (FF) [PWRF]
[ 29.760780] input: Power Button (CM) as /devices/virtual/input/input3
[ 29.776571] ACPI: Power Button (CM) [PWRB]
[ 29.776726] input: Sleep Button (CM) as /devices/virtual/input/input4
[ 29.792539] ACPI: Sleep Button (CM) [FUTS]
[ 30.137205] bttv: driver version 0.9.17 loaded
[ 30.137211] bttv: using 32 buffers with 2080k (520 pages) each for capture
[ 30.137306] bttv: Bt8xx card found (0).
[ 30.137338] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 18
[ 30.137355] bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 18, latency: 32, mmio: 0xe8002000
[ 30.137442] bttv0: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
[ 30.137478] bttv0: gpio: en=00000000, out=00000000 in=00f360ff [init]
[ 30.223382] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 30.664401] logips2pp: Detected unknown logitech mouse model 89
[ 30.822842] nvidia: module license 'NVIDIA' taints kernel.
[ 31.136228] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input6
[ 31.226959] parport_pc 00:0a: reported by Plug and Play ACPI
[ 31.227075] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 32.427717] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 33.506411] NET: Registered protocol family 10
[ 33.506780] lo: Disabled Privacy Extensions
[ 36.620341] bttv0: tuner absent
[ 36.620454] bttv0: registered device video0
[ 36.620503] bttv0: registered device vbi0
[ 36.620525] bttv0: PLL: 28636363 => 35468950 .. ok
[ 36.651247] bttv: Bt8xx card found (1).
[ 36.651285] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 36.651302] bttv1: Bt878 (rev 17) at 0000:00:0d.0, irq: 19, latency: 32, mmio: 0xe8004000
[ 36.651337] bttv1: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
[ 36.651373] bttv1: gpio: en=00000000, out=00000000 in=00f360ff [init]
[ 43.050768] bttv1: tuner absent
[ 43.051136] bttv1: registered device video1
[ 43.051361] bttv1: registered device vbi1
[ 43.051383] bttv1: PLL: 28636363 => 35468950 .. ok
[ 43.082757] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 43.083107] NVRM: loading NVIDIA Linux x86 Kernel Module 71.86.04 Mon Jan 21 11:22:18 PST 2008
[ 43.084232] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 21 (level, low) -> IRQ 21
[ 43.402083] intel8x0_measure_ac97_clock: measured 52387 usecs
[ 43.402089] intel8x0: clocking to 48000
[ 43.484680] bt878: AUDIO driver version 0.0.0 loaded
[ 43.484746] bt878: Bt878 AUDIO function found (0).
[ 43.484788] ACPI: PCI Interrupt 0000:00:09.1[A] -> GSI 17 (level, low) -> IRQ 18
[ 43.484798] bt878_probe: card id=[0x0], Unknown card.
[ 43.484800] Exiting..
[ 43.484806] ACPI: PCI interrupt for device 0000:00:09.1 disabled
[ 43.484816] bt878: probe of 0000:00:09.1 failed with error -22
[ 43.484825] bt878: Bt878 AUDIO function found (0).
[ 43.484844] ACPI: PCI Interrupt 0000:00:0d.1[A] -> GSI 19 (level, low) -> IRQ 19
[ 43.484852] bt878_probe: card id=[0x0], Unknown card.
[ 43.484853] Exiting..
[ 43.484859] ACPI: PCI interrupt for device 0000:00:0d.1 disabled
[ 43.484864] bt878: probe of 0000:00:0d.1 failed with error -22
[ 43.637622] eth0: no IPv6 routers present
[ 44.454537] lp0: using parport0 (interrupt-driven).
[ 44.539191] Adding 2265124k swap on /dev/sda5. Priority:-1 extents:1 across:2265124k
[ 45.116142] EXT3 FS on sda1, internal journal
[ 46.608876] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 47.270543] No dock devices found.
[ 50.679834] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 50.679842] apm: overridden by ACPI.
[ 56.876207] bttv0: PLL can sleep, using XTAL (28636363).
[ 58.089510] bttv1: PLL can sleep, using XTAL (28636363).
[ 65.325603] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 65.326050] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 65.326384] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 65.778165] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 65.778677] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 65.779017] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
well I'm using Ubuntu 7.10 where did you add your options at? here's a link to my initial problem, And I send this because my dmesg says bttv0: using tuner=4 under the bttv0 description, so maybe the options were added in the wrong place and therefore weren't accepted
http://www.zoneminder.com/forums/viewtopic.php?t=11886
http://www.zoneminder.com/forums/viewtopic.php?t=11886
In the second post I explained what was a few of the problems I had.
1 was 3 images on one channel . Fixed that my self 1 cam is a B&W and I had it set to gray scale. ALL cams ON a SINGLE CHIP must be set the same!!!!
The other problem that is still there is a fuzzy image that comes and goes I see small horizontal lines in the usually more the upper 1/2 of the image. this happens about once per second I get clear image then it's distorted almost like something is pulsing.
I have had at 1 time 2 of the cams hooked to a DVR and I did not see this sort of image flutter, distortion , what have you.
The other problem was after fooling with the driver I had 1 cam stop recording. Always in orange state. I deleted it and installed it as a new monitor and it seems fine.
For nasbxman's question. I remember reading somewhere that the techwell chips are not supported very well under ZM or Linux
1 was 3 images on one channel . Fixed that my self 1 cam is a B&W and I had it set to gray scale. ALL cams ON a SINGLE CHIP must be set the same!!!!
The other problem that is still there is a fuzzy image that comes and goes I see small horizontal lines in the usually more the upper 1/2 of the image. this happens about once per second I get clear image then it's distorted almost like something is pulsing.
I have had at 1 time 2 of the cams hooked to a DVR and I did not see this sort of image flutter, distortion , what have you.
The other problem was after fooling with the driver I had 1 cam stop recording. Always in orange state. I deleted it and installed it as a new monitor and it seems fine.
For nasbxman's question. I remember reading somewhere that the techwell chips are not supported very well under ZM or Linux
This is the line I put in the options file for the above dmesg
( options bttv gbuffers=32 card=77 tuner=4 radio=0 coring=1 full_luma_range=1 chroma_agc=1 combfilter=1 autoload=0 triton1=0 vsfx=0)
Now since I have 2 cards I added (,77) 1 time.
Should I also change the (gbuffers=32 ) to =64. or do you put a comma ,32 again?
As mentioned tuner=4 should be tuner=8?
Thanks
Allan
( options bttv gbuffers=32 card=77 tuner=4 radio=0 coring=1 full_luma_range=1 chroma_agc=1 combfilter=1 autoload=0 triton1=0 vsfx=0)
Now since I have 2 cards I added (,77) 1 time.
Should I also change the (gbuffers=32 ) to =64. or do you put a comma ,32 again?
As mentioned tuner=4 should be tuner=8?
Thanks
Allan
Full descriptions of options can be obtained from /usr/share/doc/kernel-doc-<Kernel_version>/Documentation/video4linux/ and it will outline what is available for your kernel version. You may have to install the kernel-doc package for it to be available or there are plenty of online references as well.
Options for you card are entered in comma separated form for each option ie:
single card:
options bttv card=77 tuner=4 radio=0
two of the same card:
options bttv card=77,77 tuner=4,4 radio=0,0
The value to the farthest left is the first device, followed by the second, followed by the third if you had one, etc, etc...
Options for you card are entered in comma separated form for each option ie:
single card:
options bttv card=77 tuner=4 radio=0
two of the same card:
options bttv card=77,77 tuner=4,4 radio=0,0
The value to the farthest left is the first device, followed by the second, followed by the third if you had one, etc, etc...
[url=http://www.freeimagehosting.net/image.p ... 8c88c1.jpg][img]http://www.freeimagehosting.net/uploads ... 8c88c1.jpg[/img][/url]
[url=http://www.freeimagehosting.net/image.p ... 070ad8.jpg][img]http://www.freeimagehosting.net/uploads ... 070ad8.jpg[/img][/url]
If this works here are to images from 1 cam one is about as good as it gets the other is fuzzed up one after the other cap 17 and cap 18
http://www.freeimagehosting.net/image.p ... 8c88c1.jpg
http://www.freeimagehosting.net/image.p ... 070ad8.jpg[/img][/code]
[url=http://www.freeimagehosting.net/image.p ... 070ad8.jpg][img]http://www.freeimagehosting.net/uploads ... 070ad8.jpg[/img][/url]
If this works here are to images from 1 cam one is about as good as it gets the other is fuzzed up one after the other cap 17 and cap 18
http://www.freeimagehosting.net/image.p ... 8c88c1.jpg
http://www.freeimagehosting.net/image.p ... 070ad8.jpg[/img][/code]
Search for interlacing:
http://en.wikipedia.org/wiki/Interlace
http://en.wikipedia.org/wiki/Interlace
Thanks
I had the frame capture rate set to 1.
Putting it at 2 got rid of most all of the flutter. But dropped the frame rate to between 1 and 2 fps
If these cards are just not worth the bother I'm looking at an 8 ch card from Blue cherry PV-149
Face it I paid 5 bucks each for these single chip cards to get a feel for the ZM program and gain the experience I have so far on the cheap.
Any thoughts on this card are welcome.
Would I get closer to 10 FPS per cam at 640x480 res
Or is the PCIe version better(pv-981). I can build a PC for 300 bucks I run it all remotely so on board video is fine and 4 gig of ram with a intel duel core should be enough?
I had the frame capture rate set to 1.
Putting it at 2 got rid of most all of the flutter. But dropped the frame rate to between 1 and 2 fps
If these cards are just not worth the bother I'm looking at an 8 ch card from Blue cherry PV-149
Face it I paid 5 bucks each for these single chip cards to get a feel for the ZM program and gain the experience I have so far on the cheap.
Any thoughts on this card are welcome.
Would I get closer to 10 FPS per cam at 640x480 res
Or is the PCIe version better(pv-981). I can build a PC for 300 bucks I run it all remotely so on board video is fine and 4 gig of ram with a intel duel core should be enough?
The PCIE is still limited by the bt878's abilities so other than being able to use that buss, I don't think there is any other advantage but also keep in mind that have not ever had a chance to test that card and really I probably should as it would fit nicely in my server 
The PV-149 is really no different from having four of your existing cards.
If you were to get the four port version, it would be like using one port on each of your existing cards.
The eight port dongle would be like using two inputs on each of your cards.
The sixteen input dongle would be same as using all four ports on each of your cards.
Performance does vary a bit by manufacturer though.
The PV-149 is really no different from having four of your existing cards.
If you were to get the four port version, it would be like using one port on each of your existing cards.
The eight port dongle would be like using two inputs on each of your cards.
The sixteen input dongle would be same as using all four ports on each of your cards.
Performance does vary a bit by manufacturer though.