[Waiting for capture daemon] with ETHER9808

Post here to ask any questions about hardware suitability, configuration in ZoneMinder, or experiences. If you just want to know if something works with ZoneMinder or not, please check the Hardware Compatibility sections in the forum, and the Wiki first. Also search this topic as well.
Post Reply
danisam
Posts: 24
Joined: Mon Oct 19, 2009 5:07 pm

[Waiting for capture daemon] with ETHER9808

Post by danisam »

Hello everybody , i can' t have the ETHER9808 working
Here i post all my configuration and error messages


My Server is
OSVER: Ubuntu Server 9.04
Kernel : 2.6.28-18-server
ZMVER: ZoneMinder 1.24.2
RAM: 1GB DDR2

I use a Card ETHER9808

And i put this in modprobe

more /etc/modprobe.d/options.conf

Code: Select all

options saa7134  card=70,70,70,70,70,70,70,70
Here is my dmesg output

Code: Select all

Linux video capture interface: v2.00
saa7134[0]: Huh, no eeprom present (err=-5)?
[    8.053992] saa7134[0]: registered device video1 [v4l2]
[    8.054022] saa7134[0]: registered device vbi1
[    8.054071] saa7134 0000:03:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    8.054080] saa7134[1]: found at 0000:03:09.0, rev: 1, irq: 17, latency: 15, mmio: 0xfdcfe000
[    8.054088] saa7134 0000:03:09.0: setting latency timer to 64
[    8.054095] saa7134[1]: subsystem: 1131:0000, board: Compro Videomate DVB-T300 [card=70,insmod option]
[    8.054145] saa7134[1]: board init: gpio is 10000
[    8.054228] input: saa7134 IR (Compro Videomate DV as /devices/pci0000:00/0000:00:1e.0/0000:02:04.0/0000:03:09.0/input/input6
[    8.196301] saa7134[1]: Huh, no eeprom present (err=-5)?
[    8.197844] saa7134[1]: registered device video2 [v4l2]
[    8.197877] saa7134[1]: registered device vbi2
[    8.197920] saa7134 0000:03:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    8.197930] saa7134[2]: found at 0000:03:0a.0, rev: 1, irq: 18, latency: 15, mmio: 0xfdcfd000
[    8.197939] saa7134 0000:03:0a.0: setting latency timer to 64
[    8.197946] saa7134[2]: subsystem: 1131:0000, board: Compro Videomate DVB-T300 [card=70,insmod option]
[    8.197993] saa7134[2]: board init: gpio is 10000
[    8.198075] input: saa7134 IR (Compro Videomate DV as /devices/pci0000:00/0000:00:1e.0/0000:02:04.0/0000:03:0a.0/input/input7
[    8.326282] saa7134[2]: Huh, no eeprom present (err=-5)?
[    8.327668] saa7134[2]: registered device video3 [v4l2]
[    8.327696] saa7134[2]: registered device vbi3
[    8.327731] saa7134 0000:03:0b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    8.327740] saa7134[3]: found at 0000:03:0b.0, rev: 1, irq: 19, latency: 15, mmio: 0xfdcfc000
[    8.327749] saa7134 0000:03:0b.0: setting latency timer to 64
[    8.327755] saa7134[3]: subsystem: 1131:0000, board: Compro Videomate DVB-T300 [card=70,insmod option]
[    8.327779] saa7134[3]: board init: gpio is 10000
[    8.327857] input: saa7134 IR (Compro Videomate DV as /devices/pci0000:00/0000:00:1e.0/0000:02:04.0/0000:03:0b.0/input/input8
[    8.456280] saa7134[3]: Huh, no eeprom present (err=-5)?
[    8.457667] saa7134[3]: registered device video4 [v4l2]
[    8.457701] saa7134[3]: registered device vbi4
[    8.457735] saa7134 0000:03:0c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    8.457744] saa7134[4]: found at 0000:03:0c.0, rev: 1, irq: 16, latency: 15, mmio: 0xfdcfb000
[    8.457752] saa7134 0000:03:0c.0: setting latency timer to 64
[    8.457758] saa7134[4]: subsystem: 1131:0000, board: Compro Videomate DVB-T300 [card=70,insmod option]
[    8.457783] saa7134[4]: board init: gpio is 10000
[    8.457860] input: saa7134 IR (Compro Videomate DV as /devices/pci0000:00/0000:00:1e.0/0000:02:04.0/0000:03:0c.0/input/input9
[    8.596280] saa7134[4]: Huh, no eeprom present (err=-5)?
[    8.597619] saa7134[4]: registered device video5 [v4l2]
[    8.597648] saa7134[4]: registered device vbi5
[    8.597680] saa7134 0000:03:0d.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    8.597689] saa7134[5]: found at 0000:03:0d.0, rev: 1, irq: 17, latency: 15, mmio: 0xfdcfa000
[    8.597697] saa7134 0000:03:0d.0: setting latency timer to 64
[    8.597703] saa7134[5]: subsystem: 1131:0000, board: Compro Videomate DVB-T300 [card=70,insmod option]
[    8.597729] saa7134[5]: board init: gpio is 10000
[    8.597803] input: saa7134 IR (Compro Videomate DV as /devices/pci0000:00/0000:00:1e.0/0000:02:04.0/0000:03:0d.0/input/input10
[    8.726280] saa7134[5]: Huh, no eeprom present (err=-5)?
[    8.727650] saa7134[5]: registered device video6 [v4l2]
[    8.727679] saa7134[5]: registered device vbi6
[    8.727713] saa7134 0000:03:0e.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    8.727722] saa7134[6]: found at 0000:03:0e.0, rev: 1, irq: 18, latency: 15, mmio: 0xfdcf9000
[    8.727730] saa7134 0000:03:0e.0: setting latency timer to 64
[    8.727736] saa7134[6]: subsystem: 1131:0000, board: Compro Videomate DVB-T300 [card=70,insmod option]
[    8.727761] saa7134[6]: board init: gpio is 10000
[    8.727837] input: saa7134 IR (Compro Videomate DV as /devices/pci0000:00/0000:00:1e.0/0000:02:04.0/0000:03:0e.0/input/input11
[    8.866296] saa7134[6]: Huh, no eeprom present (err=-5)?
[    8.867643] saa7134[6]: registered device video7 [v4l2]
[    8.867673] saa7134[6]: registered device vbi7
[    8.867711] saa7134 0000:03:0f.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    8.867720] saa7134[7]: found at 0000:03:0f.0, rev: 1, irq: 19, latency: 15, mmio: 0xfdcf8000
[    8.867729] saa7134 0000:03:0f.0: setting latency timer to 64
[    8.867736] saa7134[7]: subsystem: 1131:0000, board: Compro Videomate DVB-T300 [card=70,insmod option]
[    8.867768] saa7134[7]: board init: gpio is 10000
[    8.867848] input: saa7134 IR (Compro Videomate DV as /devices/pci0000:00/0000:00:1e.0/0000:02:04.0/0000:03:0f.0/input/input12
[    8.996282] saa7134[7]: Huh, no eeprom present (err=-5)?
[    8.997622] saa7134[7]: registered device video8 [v4l2]
[    8.997657] saa7134[7]: registered device vbi8
[    9.060113] dvb_init() allocating 1 frontend
[    9.104158] tda10046: chip is not answering. Giving up.
[    9.104317] saa7134[0]/dvb: frontend initialization failed
[    9.104362] dvb_init() allocating 1 frontend
[    9.105025] tda10046: chip is not answering. Giving up.
[    9.105175] saa7134[1]/dvb: frontend initialization failed
[    9.105222] dvb_init() allocating 1 frontend
[    9.105884] tda10046: chip is not answering. Giving up.
[    9.106032] saa7134[2]/dvb: frontend initialization failed
[    9.106077] dvb_init() allocating 1 frontend
[    9.106737] tda10046: chip is not answering. Giving up.
[    9.106886] saa7134[3]/dvb: frontend initialization failed
[    9.106930] dvb_init() allocating 1 frontend
[    9.107591] tda10046: chip is not answering. Giving up.
[    9.107738] saa7134[4]/dvb: frontend initialization failed
[    9.107783] dvb_init() allocating 1 frontend
[    9.108446] tda10046: chip is not answering. Giving up.
[    9.108614] saa7134[5]/dvb: frontend initialization failed
[    9.108676] dvb_init() allocating 1 frontend
[    9.109338] tda10046: chip is not answering. Giving up.
[    9.109506] saa7134[6]/dvb: frontend initialization failed
[    9.109569] dvb_init() allocating 1 frontend
[    9.110256] tda10046: chip is not answering. Giving up.
[    9.110427] saa7134[7]/dvb: frontend initialization failed
[    9.288939] lp: driver loaded but no devices found
My lspci -v info

Code: Select all

03:08.0 Multimedia controller: Philips Semiconductors SAA7134/SAA7135HL Video Broadcast Decoder (rev 01)
	Subsystem: Philips Semiconductors Device 0000
	Flags: bus master, medium devsel, latency 64, IRQ 16
	Memory at fdcff000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access>
	Kernel driver in use: saa7134
	Kernel modules: saa7134

X 8 times, because i have 8 SAA7134 in this card

My memory info
> free

Code: Select all

             total       used       free     shared    buffers     cached
Mem:       2052252     937168    1115084          0     339692     409732
-/+ buffers/cache:     187744    1864508
Swap:      6008268          0    6008268
My Interrupts

>cat /proc/interrupts

Code: Select all

           CPU0       CPU1       
  0:        122          0   IO-APIC-edge      timer
  1:          2          0   IO-APIC-edge      i8042
  8:          1          0   IO-APIC-edge      rtc0
  9:          0          0   IO-APIC-fasteoi   acpi
 14:          0          0   IO-APIC-edge      ata_piix
 15:          0          0   IO-APIC-edge      ata_piix
 16:        128          0   IO-APIC-fasteoi   uhci_hcd:usb5, saa7134[0], bttv0, HDA Intel, saa7134[4]
 17:          2          0   IO-APIC-fasteoi   saa7134[1], saa7134[5]
 18:          6          0   IO-APIC-fasteoi   uhci_hcd:usb4, saa7134[2], saa7134[6]
 19:     162655          0   IO-APIC-fasteoi   ata_piix, uhci_hcd:usb3, saa7134[3], saa7134[7]
 23:          0          0   IO-APIC-fasteoi   ehci_hcd:usb1, uhci_hcd:usb2
2302:       7582          0   PCI-MSI-edge      eth0
NMI:          0          0   Non-maskable interrupts
LOC:     263263     317098   Local timer interrupts
RES:       1109       1071   Rescheduling interrupts
CAL:         31         91   Function call interrupts
TLB:       3993       5210   TLB shootdowns
SPU:          0          0   Spurious interrupts
ERR:          0
MIS:          0
My ipcs -l

Code: Select all

---- Límites memoria compartida ----
número máx. segmentos = 4096
tamaño máx. segmento (kbytes) = 316800
máximo total de memoria compartida (kbytes) = 1297612800
tamaño mín. segmento (bytes) = 1

------ Límites semáforo --------
número máximo de matrices = 128
máx. semáforos por matriz = 250
máx. semáforos sistema = 32000
máx. oper. por llamada semop = 32
valor máx. semáforo = 32767

------ Mensajes: límites -------
máx. colas sistema = 1706
tamaño máx. mensaje (bytes) = 8192
tamaño máx. predeterminado cola (bytes) = 16384
My memory settings

more /etc/sysctl.conf

Code: Select all

kernel.shmall = 324403200
kernel.shmmax = 324403200
sudo zmu -U nxtview -P Nxtv13w123 -d /dev/video1 -q -v

Code: Select all

Video Device: /dev/video1
General Capabilities
  Driver: saa7134
  Card: Compro Videomate DVB-T300
  Bus: PCI:0000:03:08.0
  Version: 0.2.14
  Type: 0x5010015
    Supports video capture (X)
    Does not support video output
    Supports frame buffer overlay
    Supports VBI capture
    Does not support VBI output
    Does not support sliced VBI capture
    Does not support sliced VBI output
    Does not support video output overlay
    Has tuner
    Does not have audio in and/or out
    Does not have radio
    Supports read/write i/o (X)
    Does not support async i/o
    Supports streaming i/o (X)
    Standards:
      NTSC
      NTSC-M
      NTSC-M-JP
      NTSC-M-KR
      PAL
      PAL-BG
      PAL-H
      PAL-I
      PAL-DK
      PAL-M
      PAL-N
      PAL-Nc
      PAL-60
      SECAM
      SECAM-B
      SECAM-G
      SECAM-H
      SECAM-DK
      SECAM-L
      SECAM-Lc
  Formats:
    8 bpp gray (GREY)
    15 bpp RGB, le (RGBO)
    15 bpp RGB, be (RGBQ)
    16 bpp RGB, le (RGBP)
    16 bpp RGB, be (RGBR)
    24 bpp RGB, le (BGR3)
    24 bpp RGB, be (RGB3)
    32 bpp RGB, le (BGR4)
    32 bpp RGB, be (RGB4)
    4:2:2 packed, YUYV (YUYV)
    4:2:2 packed, UYVY (UYVY)
    4:2:2 planar, Y-Cb-Cr (422P)
    4:2:0 planar, Y-Cb-Cr (YU12)
    4:2:0 planar, Y-Cb-Cr (YV12)
Crop Capabilities
  Bounds: 720 x 578
  Default: 720 x 576
  Current: 720 x 576
Inputs: 3
  Input 0
    Name: Television
    Type: Tuner
    Audioset: 00000001
    Standards: 0xffbfff
    Power on  (X)
    Signal detected  (X)
    Colour Signal detected 
    Horizontal Lock detected 
  Input 1
    Name: Composite1
    Type: Camera
    Audioset: 00000001
    Standards: 0xffbfff
    Power on  (X)
    Signal detected  (X)
    Colour Signal detected 
    Horizontal Lock detected 
  Input 2
    Name: S-Video
    Type: Camera
    Audioset: 00000001
    Standards: 0xffbfff
    Power on  (X)
    Signal detected  (X)
    Colour Signal detected 
    Horizontal Lock detected
My error message show this errors

Code: Select all

Jun 19 16:59:32 NxtZoneMinder kernel: [  968.983715] saa7134[7]/irq: looping -- clearing PE (parity error!) enable bit
Jun 19 16:59:32 NxtZoneMinder kernel: [  968.991272] saa7134[3]/irq: looping -- clearing PE (parity error!) enable bit
Jun 19 16:59:32 NxtZoneMinder kernel: [  968.991438] saa7134[7]/irq: looping -- clearing PE (parity error!) enable bit
Jun 19 16:59:32 NxtZoneMinder kernel: [  969.007456] saa7134[3]/irq: looping -- clearing PE (parity error!) enable bit
n 21 10:27:36 NxtZoneMinder zmdc[2693]: INF [Starting pending process, zmc -d /dev/video2] 
Jun 21 10:27:36 NxtZoneMinder zmdc[2693]: INF ['zmc -d /dev/video2' starting at 10/06/21 10:27:36, pid = 3246] 
Jun 21 10:27:36 NxtZoneMinder zmdc[2693]: INF [Starting pending process, zmc -d /dev/video5] 
Jun 21 10:27:36 NxtZoneMinder zmdc[2693]: INF ['zmc -d /dev/video5' starting at 10/06/21 10:27:36, pid = 3247] 
Jun 21 10:27:36 NxtZoneMinder zmdc[3246]: INF ['zmc -d /dev/video2' started at 10/06/21 10:27:36] 
Jun 21 10:27:36 NxtZoneMinder zma_m25[2734]: WAR [Waiting for capture daemon]
Jun 21 10:27:36 NxtZoneMinder zmdc[3247]: INF ['zmc -d /dev/video5' started at 10/06/21 10:27:36] 
Jun 21 10:27:36 NxtZoneMinder zmc_dvideo2[3246]: INF [Debug Level = 0, Debug Log = <none>]
Jun 21 10:27:36 NxtZoneMinder zmc_dvideo5[3247]: INF [Debug Level = 0, Debug Log = <none>]
Jun 21 10:27:36 NxtZoneMinder zmc_dvideo2[3246]: INF [New Debug Level = 4, New Debug Log = /tmp/zm_debug.log.03246]
Jun 21 10:27:36 NxtZoneMinder zmc_dvideo5[3247]: INF [New Debug Level = 4, New Debug Log = /tmp/zm_debug.log.03247]
Jun 21 10:27:36 NxtZoneMinder zmc_dvideo2[3246]: INF [Starting Capture]
Jun 21 10:27:36 NxtZoneMinder zmc_dvideo5[3247]: INF [Starting Capture]
Jun 21 10:27:36 NxtZoneMinder zma_m24[2725]: WAR [Waiting for capture daemon]
Jun 21 10:27:37 NxtZoneMinder zmdc[2693]: INF [Starting pending process, zmc -d /dev/video8] 
Jun 21 10:27:37 NxtZoneMinder zmdc[3248]: INF ['zmc -d /dev/video8' started at 10/06/21 10:27:37] 
Jun 21 10:27:37 NxtZoneMinder zmdc[2693]: INF ['zmc -d /dev/video8' starting at 10/06/21 10:27:37, pid = 3248] 
Jun 21 10:27:37 NxtZoneMinder zma_m25[2734]: WAR [Waiting for capture daemon]
Jun 21 10:27:37 NxtZoneMinder zmc_dvideo8[3248]: INF [Debug Level = 0, Debug Log = <none>]
Jun 21 10:27:37 NxtZoneMinder zmc_dvideo8[3248]: INF [New Debug Level = 4, New Debug Log = /tmp/zm_debug.log.03248]
Jun 21 10:27:37 NxtZoneMinder zmc_dvideo8[3248]: INF [Starting Capture]
Jun 21 10:27:37 NxtZoneMinder zma_m24[2725]: WAR [Waiting for capture daemon]
Jun 21 10:27:38 NxtZoneMinder zma_m25[2734]: WAR [Waiting for capture daemon]
Jun 21 10:27:38 NxtZoneMinder zma_m24[2725]: WAR [Waiting for capture daemon]
Jun 21 10:27:39 NxtZoneMinder zma_m25[2734]: WAR [Waiting for capture daemon]
Jun 21 10:27:39 NxtZoneMinder zma_m24[2725]: WAR [Waiting for capture daemon]
To download the complete message file.

Thanks you very much for your help.

Regards
Last edited by danisam on Fri Jun 25, 2010 11:17 pm, edited 1 time in total.
Top
danisam
Posts: 24
Joined: Mon Oct 19, 2009 5:07 pm

Post by danisam »

I Have some good and bad news.

Right know the card works

I changed the file options.conf in modprobe.d directory to options and the line

Code: Select all

options saa7134  card=70,70,70,70,70,70,70,70
by

Code: Select all

options saa7134  card=60,60,60,60,60,60,60,60
But i thinks i have an instability of the system , in the logs i saw some of this lines

Code: Select all

 WAR [Capture failure, possible signal loss?: Input/output error]
Could you help me to fix this error mesage.

Thank you very much.

Best regards
Top
danisam
Posts: 24
Joined: Mon Oct 19, 2009 5:07 pm

Post by danisam »

Finnaly i have the system working well 1 hour , and after the Ubuntu server Crash completely.

maybe is a conflict between the card and the system.

Did you see some bad things i my Proc/Interrups ?
Top
Post Reply

Return to “Hardware Queries”