[solved]BL-C1 Camera not work in zoneminder

cmf · Post by **cmf** » Thu Jan 13, 2011 7:51 am

I can visit the camera via
http://192.168.1.253:2000/CgiStart/Imag ... on=320x240
but when I visit the camear via zoneminder,
which i set the remote host name as : username:passwrd@192.168.1.253
remote host path as:/CgiStart/ImageViewer?Resolution=320x240

the source turns red and the screen of the zoneminder turns black, is there anybody knows how to solve it?

bb99 · Post by **bb99** » Thu Jan 13, 2011 11:33 am

Try: /nphContinuousServerPush?Resolution=640x480&Quality=Standard

http://www.zoneminder.com/forums/viewto ... light=blc1

PacoLM · Post by **PacoLM** » Thu Jan 13, 2011 12:32 pm

Did you set also the port to 2000?

cmf · Post by **cmf** » Fri Jan 14, 2011 1:46 am

bb99 wrote:Try: /nphContinuousServerPush?Resolution=640x480&Quality=Standard

http://www.zoneminder.com/forums/viewto ... light=blc1

HI, I have read the post and following the instruction on that post but still get no hope

now my host name is: username:passwrd@192.168.1.253
and the host port is: 2000
and the host path is : /nphContinuousServerPush?Resolution=640x480&Quality=Standard

the status of source turns "orange" and the video is "black" now

cmf · Post by **cmf** » Fri Jan 14, 2011 1:47 am

PacoLM wrote:Did you set also the port to 2000?

yup,
my camera is BL-C1E, is there any different between BLC1 and BLC1E on the setting?

cmf · Post by **cmf** » Fri Jan 14, 2011 1:55 am

my setting is shown below

bb99 · Post by **bb99** » Fri Jan 14, 2011 6:20 pm

Oh so close, orange is progress. Now change "capture width" to 320 and "capture height" to 240; change the remote host path to "/nphContinuousServerPush?Resolution=320x240&Quality=Standard" and set the camera to the same resolution, double check the port 2000 on the camera and see what happens. Make sure the monitor function is set to monitor and the camera is enabled. You will not get green results until you change from monitor to something else, like Modect.

wipeout · Post by **wipeout** » Fri Jan 14, 2011 7:26 pm

Try with this:
in the source tab
=======================
Remote Protocol: RTSP
Remote Method: RTP/Unicast
Remote Host Name: your camera ip
Remote Host Port: your port
Remote Host Path: /nphMpeg4/nil-320x240
or
Remote Host Path: /nphMpeg4/nil-640x480
=======================

Bye!

cmf · Post by **cmf** » Mon Jan 17, 2011 2:58 am

bb99 wrote:Oh so close, orange is progress. Now change "capture width" to 320 and "capture height" to 240; change the remote host path to "/nphContinuousServerPush?Resolution=320x240&Quality=Standard" and set the camera to the same resolution, double check the port 2000 on the camera and see what happens. Make sure the monitor function is set to monitor and the camera is enabled. You will not get green results until you change from monitor to something else, like Modect.

it works now, thank you very much

bb99 · Post by **bb99** » Mon Jan 17, 2011 4:53 am

Please edit your original post title with "solved"; makes searching the forums so much easier. Now you can play with the resolution keeping in mind the shared memory settings may need to be changed for 640*480 to work.