NO RECORD ON IP CAMERA

[dj_pato]

Hello everyone,

The program starts and after a few seconds it stops working

DEBUG:
May 11 02:02:46 FCM-Security-Server zmdc[3685]: INF [Starting pending process, zmc -m 2]
May 11 02:02:46 FCM-Security-Server zmdc[3685]: INF ['zmc -m 2' starting at 11/05/11 02:02:46, pid = 3727]
May 11 02:02:46 FCM-Security-Server zmdc[3727]: INF ['zmc -m 2' started at 11/05/11 02:02:46]
May 11 02:02:46 FCM-Security-Server zmc_m2[3727]: INF [Debug Level = 0, Debug Log = <none>]
May 11 02:02:46 FCM-Security-Server zmc_m2[3727]: INF [Starting Capture]
May 11 02:02:48 FCM-Security-Server zmc_m2[3727]: ERR [Select timed out]
May 11 02:02:48 FCM-Security-Server zmc_m2[3727]: ERR [Unable to read content]
May 11 02:02:48 FCM-Security-Server zmc_m2[3727]: ERR [Unable to get response]
May 11 02:02:48 FCM-Security-Server zmc_m2[3727]: ERR [Failed to capture image from monitor 2 (0/1)]
May 11 02:02:48 FCM-Security-Server zmdc[3685]: ERR ['zmc -m 2' exited abnormally, exit status 255]
May 11 02:02:58 FCM-Security-Server zmdc[3685]: INF [Starting pending process, zmc -m 2]
May 11 02:02:58 FCM-Security-Server zmdc[3685]: INF ['zmc -m 2' starting at 11/05/11 02:02:58, pid = 3729]
May 11 02:02:58 FCM-Security-Server zmdc[3729]: INF ['zmc -m 2' started at 11/05/11 02:02:58]
May 11 02:02:58 FCM-Security-Server zmc_m2[3729]: INF [Debug Level = 0, Debug Log = <none>]
May 11 02:02:58 FCM-Security-Server zmc_m2[3729]: INF [Starting Capture]
May 11 02:03:00 FCM-Security-Server zmc_m2[3729]: ERR [Select timed out]
May 11 02:03:00 FCM-Security-Server zmc_m2[3729]: ERR [Unable to read content]
May 11 02:03:00 FCM-Security-Server zmc_m2[3729]: ERR [Unable to get response]
May 11 02:03:00 FCM-Security-Server zmc_m2[3729]: ERR [Failed to capture image from monitor 2 (0/1)]
May 11 02:03:00 FCM-Security-Server zmdc[3685]: ERR ['zmc -m 2' exited abnormally, exit status 255]

I GOOGLE THIS PROBLEM BUT I CAN´T FIND ANY SOLUTION!


HELPPP PLEASE!!!


THANKSSSSSSSSSSSSSS

[Flasheart]

Not enough information.

What ip camera is it, and what are your settings in the monitor (source tab) ?

[dj_pato]

This is the camera:

300k-pixel-ip-network-internet-surveillance-ip-camera-35425
ON DEALEXTREME
(Cannot put URLs SORRY!)

Mi config for the camera is:

Remote Protocol HTTP
Remote Method Simple
Remote Host Name 192.168.120.2
Remote Host Port 80
Remote Host Path /image.jpg
Remote Image Colours 24 bit colour
Capture Width (pixels) 640
Capture Height (pixels) 480


The camera works OK but zoneminder stops working after a few seconds!

HELP PLEASE!

[Flasheart]

When you visit http://192.168.120.2/image.jpg in a browser you get a static jpg that is exactly 640x480?

If so, great. But zm won't work out of the box on 640x480 without a quick tweak.

Now - read the FAQ and follow the steps in the section on shared memory;

http://www.zoneminder.com/wiki/index.ph ... esolutions.

If you're still having problems after doing that, check your logs - zm.log or relevant bits from syslog and post any likely looking error messages back here.

[KeithB]

What frame rate are you using and did you set it on the camera or in Zoneminder?