Posted: Wed Feb 11, 2009 5:01 pm
That's fine. I just wanted to make sure I was testing the same scenario.
+1 hereWhen I configure for V4L2, one monitor will work fine on either channel 0 or 1, but if I enable a second channel on a port I get nothing on either.
Error with both 0 and 1 set to modect:
Also note that zmc ignores the debug setting which is enabled.
Code: Select all
Feb 10 11:36:42 archbox zmpkg[12258]: INF [Command: start]
Feb 10 11:36:42 archbox zmdc[12275]: INF [Server starting at 09/02/10 11:36:42]
Feb 10 11:36:45 archbox zmdc[12302]: INF ['zmc -d /dev/video0' started at 09/02/10 11:36:45]
Feb 10 11:36:45 archbox zmc_dvideo0[12302]: INF [Debug Level = 0, Debug Log = <none>]
Feb 10 11:36:45 archbox zmdc[12275]: INF ['zmc -d /dev/video0' starting at 09/02/10 11:36:45, pid = 12302]
Feb 10 11:36:46 archbox zmc_dvideo0[12302]: INF [Starting Capture]
Feb 10 11:36:46 archbox zmdc[12309]: INF ['zma -m 1' started at 09/02/10 11:36:46]
Feb 10 11:36:46 archbox zma_m1[12309]: INF [Debug Level = 0, Debug Log = <none>]
Feb 10 11:36:46 archbox zma_m1[12309]: WAR [Waiting for capture daemon]
Feb 10 11:36:46 archbox zmdc[12275]: INF ['zma -m 1' starting at 09/02/10 11:36:46, pid = 12309]
Feb 10 11:36:46 archbox zmdc[12275]: INF ['zmc -d /dev/video0' already running at 09/02/10 11:36:45, pid = 12302]
Feb 10 11:36:46 archbox zmdc[12315]: INF ['zma -m 2' started at 09/02/10 11:36:46]
Feb 10 11:36:46 archbox zma_m2[12315]: INF [Debug Level = 0, Debug Log = <none>]
Feb 10 11:36:46 archbox zma_m2[12315]: WAR [Waiting for capture daemon]
Feb 10 11:36:46 archbox zmdc[12275]: INF ['zma -m 2' starting at 09/02/10 11:36:46, pid = 12315]
Feb 10 11:36:46 archbox zmdc[12319]: INF ['zmfilter.pl' started at 09/02/10 11:36:46]
Feb 10 11:36:46 archbox zmdc[12275]: INF ['zmfilter.pl' starting at 09/02/10 11:36:46, pid = 12319]
Feb 10 11:36:47 archbox zma_m1[12309]: WAR [Waiting for capture daemon]
Feb 10 11:36:47 archbox zmdc[12323]: INF ['zmaudit.pl -c' started at 09/02/10 11:36:47]
Feb 10 11:36:47 archbox zmdc[12275]: INF ['zmaudit.pl -c' starting at 09/02/10 11:36:47, pid = 12323]
Feb 10 11:36:47 archbox zmfilter[12319]: INF [Scanning for events]
Feb 10 11:36:47 archbox zma_m2[12315]: WAR [Waiting for capture daemon]
Feb 10 11:36:47 archbox zmdc[12328]: INF ['zmwatch.pl' started at 09/02/10 11:36:47]
Feb 10 11:36:47 archbox zmdc[12275]: INF ['zmwatch.pl' starting at 09/02/10 11:36:47, pid = 12328]
Feb 10 11:36:48 archbox zma_m1[12309]: WAR [Waiting for capture daemon]
Feb 10 11:36:48 archbox zmwatch[12328]: INF [Watchdog starting]
Feb 10 11:36:48 archbox zmwatch[12328]: INF [Watchdog pausing for 30 seconds]
Feb 10 11:36:48 archbox zmdc[12336]: INF ['zmupdate.pl -c' started at 09/02/10 11:36:48]
Feb 10 11:36:48 archbox zmdc[12275]: INF ['zmupdate.pl -c' starting at 09/02/10 11:36:48, pid = 12336]
Feb 10 11:36:48 archbox zma_m2[12315]: WAR [Waiting for capture daemon]
Feb 10 11:36:49 archbox zma_m1[12309]: WAR [Waiting for capture daemon]
Feb 10 11:36:49 archbox zma_m2[12315]: WAR [Waiting for capture daemon]
Feb 10 11:36:50 archbox zma_m1[12309]: WAR [Waiting for capture daemon]
Feb 10 11:36:50 archbox zma_m2[12315]: WAR [Waiting for capture daemon]
Feb 10 11:36:51 archbox zma_m1[12309]: WAR [Waiting for capture daemon]
With this config watch stream works on channel 1
Code: Select all
Feb 10 11:29:39 archbox zmdc[11342]: INF ['zmupdate.pl -c' starting at 09/02/10 11:29:39, pid = 11394]
Feb 10 11:29:39 archbox zmc_dvideo0[11368]: ERR [Expected buffer for channel 1, video buffer input is 0]
Feb 10 11:29:40 archbox zmc_dvideo0[11368]: ERR [Expected buffer for channel 1, video buffer input is 0]