Page 2 of 2
Re: unable to open input
Posted: Fri Sep 09, 2022 4:08 pm
by Heimo
Heimo wrote: ↑Fri Sep 09, 2022 4:07 pm
iconnor wrote: ↑Fri Sep 09, 2022 4:01 pm
So the no route to host are obvious.
The rest is basically saying that it is taking too long for ffmpeg to figure out what the stream is.
You might try setting the Options feild to probesize=50000
You might also have to adjust Options->System->WATCH_MAX_DELAY larger.
I take it these are older cams? I wouldn't expect the keyframe interval to be too huge, but maybe so...
it does not work.
I have set the rate to 3 and the interval to 10
you are right, these are older cams
Re: unable to open input
Posted: Fri Sep 09, 2022 4:09 pm
by Heimo
Heimo wrote: ↑Fri Sep 09, 2022 4:08 pm
Heimo wrote: ↑Fri Sep 09, 2022 4:07 pm
iconnor wrote: ↑Fri Sep 09, 2022 4:01 pm
So the no route to host are obvious.
The rest is basically saying that it is taking too long for ffmpeg to figure out what the stream is.
You might try setting the Options feild to probesize=50000
You might also have to adjust Options->System->WATCH_MAX_DELAY larger.
I take it these are older cams? I wouldn't expect the keyframe interval to be too huge, but maybe so...
it does not work.
I have set the rate to 3 and the interval to 10
you are right, these are older cams
I have set the rate to 3 and the interval to 10 -> on the cam
Re: unable to open input
Posted: Fri Sep 09, 2022 6:02 pm
by Magic919
Sorted now?
Re: unable to open input
Posted: Fri Sep 09, 2022 6:26 pm
by Heimo
Magic919 wrote: ↑Fri Sep 09, 2022 6:02 pmSorted now?
no, does not work
Re: unable to open input
Posted: Fri Sep 09, 2022 6:47 pm
by iconnor
So vlc works with the url what about ffplay?
I use 1.36.25 with lots of old Axis and Foscam cameras. Nothing special about them, they should work fine.
Re: unable to open input
Posted: Fri Sep 09, 2022 6:49 pm
by Heimo
iconnor wrote: ↑Fri Sep 09, 2022 6:47 pm
So vlc works with the url what about ffplay?
I use 1.36.25 with lots of old Axis and Foscam cameras. Nothing special about them, they should work fine.
Is it possible to get the parameters you use of all pages? I am using for instance FI9826P V2
They worked very well eith 1.32
Re: unable to open input
Posted: Fri Sep 09, 2022 6:55 pm
by iconnor
I see that with my foscams I have specified port 80 for the rtsp stream... rtsp://192.168.2.17:80/videoMain
Which is weird, but whatever.
Re: unable to open input
Posted: Fri Sep 09, 2022 6:58 pm
by Magic919
What’s the deal with the no route host errors?
Re: unable to open input
Posted: Sat Sep 10, 2022 11:12 am
by Heimo
It works with remote and rtsp/unicast This is ok.
Thanks for your help.
Regards
Heimo
Re: unable to open input
Posted: Sat Apr 29, 2023 9:30 am
by Heimo
Dear all,
after installing a new cam, I had the same problem. Same cams, one works, one did not with the same parameter.
Now I think I have found the problem and the solution, hopefully.
Hardware:
raspberry PI 4 wit 4GB RAM
cams which did not work: foscam wiht ffmpeg
ZM 1.36.33
I encreased the GPU MEM from 64MB to 128 MB and now it works fine
Best greetings from Lower Austria.
Heimo