Page 2 of 5
Not that you are listening...but...lol
Posted: Thu Nov 09, 2006 6:59 pm
by mrd
I got it to work... sort of. For some odd reason, the new control just started showing up in the dropdown, but now I'm trying to figure out all of correct values to put into the control settings.
I'll try to figure them out from the code, but it sure would be nice if you had a document taht helps...
Thanks,
Posted: Tue Nov 14, 2006 11:02 pm
by zoneminder
I can help, if you can be more specific in your questions or requirements.
Go Pats!!
Posted: Wed Nov 15, 2006 2:48 am
by mrd
Ahh... Finally some attention....lol
I'm trying to figure out what all of the numeric values should be for a PTZ-2N in the control settings for the control type that I added. There are fields that ask for things like "max pan", "max tilt", "max step". I'm not sure where I can get this information and the control script that I'm working with doesn't seem to spell it out clearly enough for me. I'm assuming all of this can be found in some spec document for the camera, but I've searched the entire net and can't seem to find one.
Please help... if you can.
P.S. The Pats need even more help than I do...lol
Posted: Wed Nov 15, 2006 10:07 am
by zoneminder
Essentially those values mean the maximum values that the camera wil accept. They are used to determine what is sent when you click on the arrows etc in the control screeen. Clicking near the point of the arrow will send the maximum, at the other end will send the minimum. I can't help you with what the values are, if you don't have a spec then you may have to experiment by calling your script directly with a range of values and seeing what your cam responds to. Some may be obvious, for instance if pan speed is a byte in your script's protocol, then 255 is an obvious maximum to try.
Posted: Wed Nov 15, 2006 11:43 pm
by mrd
i see...
I'm surprized that with everyone who is using zoneminder that no one seems to know these values for the PTZ-2N. If I do manage to figure them out, I'll be sure to post it in here.
Thanks!
Posted: Wed Nov 15, 2006 11:58 pm
by cordel
They are defined in the
README
The database values are mostly set to 1 (capable) or 0 (not capable) to describe what the camera is capable of.
Regards,
Corey
I'm a fool...
Posted: Thu Nov 16, 2006 9:15 pm
by mrd
Next time I'll try looking right in front of me first...
Thanks!
Been out of the loop
Posted: Sat Apr 14, 2007 6:10 am
by gneuf
I guess I haven't been getting my notices from this thread. Sorry.
I just noticed that the server with the code didn't have the code there anymore...
I've put it back so now it can be downloaded.
I see questions about the ptel control setup.
I'll try to go to the wiki and layout all the values I use for the PictureTel control setup.
Posted: Sat Apr 14, 2007 1:49 pm
by mrd
I'm still interested!..
Posted: Sun Dec 02, 2007 10:51 pm
by gneuf
Ok, I finally got to the Sony SNC-M3W patches, control script, and Wiki page.
I'll use the Wiki page for a template for the PTZ Wiki entry sometime this week...
Posted: Sun Dec 02, 2007 11:13 pm
by mrd
Any chance of getting a PTZ-4N control script?
Posted: Mon Dec 03, 2007 1:05 am
by gneuf
Absolutely! Just send me a PTZ4N.
Posted: Mon Dec 03, 2007 1:09 am
by mrd
send me your address...
I'd be happy to.
Posted: Mon Dec 03, 2007 1:13 am
by gneuf
Gimme a minute to scare up the PictureTel V2/V3 control command set and have a look...they enhanced the V1 command set (PTZ1/PTZ2 series cameras) for the subsequent cameras...
Is it serial or RS422?
-g
Posted: Mon Dec 03, 2007 1:19 am
by mrd
Hm... not sure, it has the same connector on it as the PTZ-2N but none of the controls work with the 2N script.