Windows Live Viewer..27-11-05 Now Complete Frontend for ZM!!

R2D2 · Post by **R2D2** » Tue Aug 08, 2006 6:38 pm

jameswilson wrote:ok go into settings in zm4ms clcik the paths tab and remove nph- from the live view path setting. You should be done then

Done, but zm4ms works still not yet.

jameswilson · Post by **jameswilson** » Tue Aug 08, 2006 6:46 pm

ok then i need to see a screen shot of your monitor settings in zm and in zm4ms

R2D2 · Post by **R2D2** » Tue Aug 08, 2006 7:05 pm

zm4ms you can see on page 25 in my posting.
Here are my monitor settings on ZM:

jameswilson · Post by **jameswilson** » Tue Aug 08, 2006 7:46 pm

ah just noticed a couple of things
monitor 2 has 2.. in the address remove 1
and you need to add a ':' infront of the port number if using anything other than 80, if using 80 then leave blank or insert :80

R2D2 · Post by **R2D2** » Tue Aug 08, 2006 7:55 pm

jameswilson wrote:ah just noticed a couple of things
monitor 2 has 2.. in the address remove 1
and you need to add a ':' infront of the port number if using anything other than 80, if using 80 then leave blank or insert :80

Done, but zm4ms works still not yet.

jameswilson · Post by **jameswilson** » Tue Aug 08, 2006 8:23 pm

ok then im starting to run out of ideas, i can only assume you have your monitor numbers mixed up. Can you post a screenshot of your console

R2D2 · Post by **R2D2** » Wed Aug 09, 2006 2:53 pm

jameswilson · Post by **jameswilson** » Wed Aug 09, 2006 10:50 pm

ok then i cant see anything obvious here either.
I will need to see a full path, remember eairlier how you git a path to the image eg http://1.1.1.1/zms?etcetc.
get that path and put in a browser and check you get an image, if you do post that complete path so i can see what it looks like

R2D2 · Post by **R2D2** » Sat Aug 12, 2006 6:39 am

Is it this what you mean?

When i type:
http://192.168.178.20/cgi-bin/zms?mode= ... 1155363699
in the Adressline of my Browser i can see the Picture.

btw: i have installed Cambozola, works fine.

jameswilson · Post by **jameswilson** » Sat Aug 12, 2006 10:55 am

can you post your zm4ms live view path

becaus ethat should work

R2D2 · Post by **R2D2** » Sat Aug 12, 2006 6:45 pm

jameswilson wrote:can you post your zm4ms live view path

becaus ethat should work

The Path is:
/cgi-bin/zms

jameswilson · Post by **jameswilson** » Sat Aug 12, 2006 6:55 pm

im lost then im afraid. I have never tried without aut and can only assume thats the issue.
If you put the whole path from the p[revious post "the one you put in a browser) and enable url mode that will work for live view

R2D2 · Post by **R2D2** » Sat Aug 12, 2006 7:09 pm

jameswilson wrote:im lost then im afraid. I have never tried without aut and can only assume thats the issue.

Where can i enable the Authentication?

jameswilson · Post by **jameswilson** » Sat Aug 12, 2006 7:30 pm

you enable it in zm. I have never tested but before you do that check my previous suggestion of running zm4ms in url mode, just to check all is working before you enable auth. Maybe someone else has tried zm4ms without auth?

R2D2 · Post by **R2D2** » Sat Aug 12, 2006 7:44 pm

jameswilson wrote:you enable it in zm. I have never tested but before you do that check my previous suggestion of running zm4ms in url mode, just to check all is working before you enable auth. Maybe someone else has tried zm4ms without auth?

And how can switch zm4ms into "url mode"???