ZoneMinder Forums

damn me,
probably i was burned, a little tired after this marathon of 20 hours on
this F#@king delicius asus barebone


but ok, i resolve all the issue about installing zm on slack12,
but appear that the gremlin on my back is always alive and kicking..

some info useful for debug (or help):

root@videoserver:~# cat /proc/interrupts
CPU0
0: 142804 XT-PIC-XT timer
1: 2 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
3: 125 XT-PIC-XT ohci1394, bttv3, bttv7, bt878
5: 108 XT-PIC-XT ATI IXP, bttv0, bttv4, bt878
7: 2 XT-PIC-XT parport0
8: 1 XT-PIC-XT rtc
9: 1 XT-PIC-XT acpi
10: 94 XT-PIC-XT ehci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3, bttv2, bttv6, bt878
11: 2032 XT-PIC-XT yenta, bttv1, bttv5, bt878, eth0
12: 4 XT-PIC-XT i8042
14: 22426 XT-PIC-XT ide0
NMI: 0
ERR: 0


root@videoserver:~# lsmod
Module Size Used by
snd_seq_dummy 2692 0
snd_seq_oss 28032 0
snd_seq_midi_event 5888 1 snd_seq_oss
snd_seq 42576 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 6540 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 38432 0
snd_mixer_oss 13824 1 snd_pcm_oss
ipv6 226016 28
capability 3336 0
commoncap 5376 1 capability
lp 9800 0
bt878 8872 0
parport_pc 23844 1
parport 30152 2 lp,parport_pc
pcspkr 2304 0
psmouse 34440 0
pcmcia 30628 0
bttv 168436 1 bt878
video_buf 20228 1 bttv
ir_common 29956 1 bttv
compat_ioctl32 1280 1 bttv
btcx_risc 3976 1 bttv
tveeprom 13712 1 bttv
videodev 25344 1 bttv
v4l2_common 14848 2 bttv,videodev
v4l1_compat 13700 2 bttv,videodev
yenta_socket 23180 1
rsrc_nonstatic 10880 1 yenta_socket
serio_raw 5124 0
pcmcia_core 32400 3 pcmcia,yenta_socket,rsrc_nonstatic
8139too 20864 0
mii 4736 1 8139too
ati_agp 6924 1
i2c_piix4 7436 0
shpchp 29204 0
agpgart 26928 1 ati_agp
ata_generic 5252 0
evdev 7936 0
pata_atiixp 5504 0
snd_atiixp 15116 0
snd_ac97_codec 96292 1 snd_atiixp
ac97_bus 2048 1 snd_ac97_codec
snd_pcm 65160 3 snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer 17540 2 snd_seq,snd_pcm
snd 41956 9 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
soundcore 5728 1 snd
snd_page_alloc 7432 2 snd_atiixp,snd_pcm




lspci -v
00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
Subsystem: ASUSTeK Computer Inc. Unknown device 8107
Flags: bus master, 66MHz, medium devsel, latency 64
Memory at f0000000 (32-bit, prefetchable)
Memory at feb00000 (32-bit, non-prefetchable)
Capabilities: [a0] AGP version 3.0

00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP PCI/AGP Bridge (prog-if
00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fd900000-fdcfffff
Prefetchable memory behind bridge: dde00000-eddfffff

00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev 01) (pr
og-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe800000 (32-bit, non-prefetchable)

00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev 01) (pr
og-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe900000 (32-bit, non-prefetchable)

00:13.2 USB Controller: ATI Technologies Inc EHCI USB Controller (rev 01) (prog-
if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fea00000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 2

00:14.0 SMBus: ATI Technologies Inc SMBus (rev 18)
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: 66MHz, medium devsel
I/O ports at 0a00
Memory at 40000000 (32-bit, non-prefetchable)

00:14.1 IDE interface: ATI Technologies Inc Dual Channel Bus Master PCI IDE Cont
roller (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 01f0
I/O ports at 03f4


00:14.3 ISA bridge: ATI Technologies Inc Unknown device 434c
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, 66MHz, medium devsel, latency 0

00:14.4 PCI bridge: ATI Technologies Inc Unknown device 4342 (prog-if 01 [Subtractive decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=08, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: fdd00000-fe0fffff
Prefetchable memory behind bridge: ede00000-efdfffff

00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller
Subsystem: ASUSTeK Computer Inc. Unknown device 810d
Flags: bus master, 66MHz, slow devsel, latency 64, IRQ 5
Memory at fe700000 (32-bit, non-prefetchable)

01:05.0 VGA compatible controller: ATI Technologies Inc Radeon 9100 PRO IGP (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device 8107
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11
Memory at e0000000 (32-bit, prefetchable) [size=128M]
I/O ports at d000 [size=256]
Memory at fdc00000 (32-bit, non-prefetchable) [size=64K]

Expansion ROM at fdb00000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Capabilities: [50] Power Management version 2

02:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at e800 [size=256]
Memory at fe000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

02:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if
10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A8V Deluxe or A8N-VM CSM Mainboard
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at fdf00000 (32-bit, non-prefetchable) [size=2K]
I/O ports at ec00 [size=128]
Capabilities: [50] Power Management version 2

02:0c.0 CardBus bridge: ENE Technology Inc CB-710/2/4 Cardbus Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8131
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at fdd00000 (32-bit, non-prefetchable) [size=4K]


Bus: primary=02, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 44000000-47fff000 (prefetchable)
Memory window 1: 48000000-4bfff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
16-bit legacy interface ports at 0001

02:0c.1 FLASH memory: ENE Technology Inc CB710 Memory Card Reader Controller
Subsystem: ASUSTeK Computer Inc. Unknown device 1724
Flags: medium devsel, IRQ 10
I/O ports at e480 [size=128]
Capabilities: [a0] Power Management version 2

02:0e.0 PCI bridge: Hint Corp HiNT HB4 PCI-PCI Bridge (PCI6150) (rev 04) (prog-if 00 [Normal dec
ode])
Flags: bus master, medium devsel, latency 64
Bus: primary=02, secondary=04, subordinate=04, sec-latency=64
Prefetchable memory behind bridge: 00000000ede00000-00000000efdfffff
Capabilities: [dc] Power Management version 1
Capabilities: [e4] #06 [0094]
Capabilities: [e8] Vital Product Data

04:08.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at efc00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at efd00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at efa00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at efb00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ef800000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ef900000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0b.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at ef600000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0b.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at ef700000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0c.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at ef400000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at ef500000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0d.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at ef200000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at ef300000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data

Capabilities: [4c] Power Management version 2

04:0e.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ef000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0e.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ef100000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0f.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at eee00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0f.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at eef00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2


------------------------

the card is in modprobe
as 102,102,102,102,102,102,102,102

but something goes wrong cause i've black screens and not blue one..

somene can help?

Have you verified that the card is loading correctly?
dmesg |grep bttv

Hi Cordel, and thanks for the answer,
i use this card on a previous zm installation (and it work perfectly for about 1 year and half) defining in modprobe options tuner=-1 radio=-1 card=77,77,77,77,77,77,77,77

the dev videos work all (on prev. installation)


now, i read on some post here that this card work better with 8x 102's card,
but now i'm not so sure, appear that the boot was very very long (more than 2 mins) and what leave me stoned is the presence of "audio capture devices",
that i've not for sure.
Now i can't try again till tomorrow (i leave the server on final site and still not yet implemented the remote connection, to save this night to me, cause i'm a bit tired now )
Maybe is the V4L2 that is different (on prev. i used the old V4L )

but definitely i will force this card to work, want it or not i need to restart the video surveillance there.

Tomorrow i try to reset to 77 the card type.

and post the result.
best wishes

Some input from the logs might be useful.

here the
dmesg | grep bttv

result.. maybe there is some trouble here..

bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:04:08.0, irq: 5, latency: 64, mmio: 0xefc00000
bttv0: using: IVC-200 [card=102,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... <6>cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (1).
bttv1: Bt878 (rev 17) at 0000:04:09.0, irq: 11, latency: 64, mmio: 0xefa00000
bttv1: using: IVC-200 [card=102,insmod option]
bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv1: using tuner=-1
bttv1: i2c: checking for MSP34xx @ 0x80... not found
bttv1: i2c: checking for TDA9875 @ 0xb0... not found
bttv1: i2c: checking for TDA7432 @ 0x8a... not found
bttv1: i2c: checking for TDA9887 @ 0x86... not found
bttv1: registered device video1
bttv1: registered device vbi1
bttv1: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (2).
bttv2: Bt878 (rev 17) at 0000:04:0a.0, irq: 10, latency: 64, mmio: 0xef800000
bttv2: using: IVC-200 [card=102,insmod option]
bttv2: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv2: using tuner=-1
bttv2: i2c: checking for MSP34xx @ 0x80... not found
bttv2: i2c: checking for TDA9875 @ 0xb0... not found
bttv2: i2c: checking for TDA7432 @ 0x8a... not found
bttv2: i2c: checking for TDA9887 @ 0x86... not found
bttv2: registered device video2
bttv2: registered device vbi2
bttv2: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (3).
bttv3: Bt878 (rev 17) at 0000:04:0b.0, irq: 3, latency: 64, mmio: 0xef600000
bttv3: using: IVC-200 [card=102,insmod option]
bttv3: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv3: using tuner=-1
bttv3: i2c: checking for MSP34xx @ 0x80... not found
bttv3: i2c: checking for TDA9875 @ 0xb0... not found
bttv3: i2c: checking for TDA7432 @ 0x8a... <6>Adding 4915848k swap on /dev/hdb5. Priority:-1 extents:1 across:4915848k
bttv3: i2c: checking for TDA9887 @ 0x86... not found
bttv3: registered device video3
bttv3: registered device vbi3
bttv3: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (4).
bttv4: Bt878 (rev 17) at 0000:04:0c.0, irq: 5, latency: 64, mmio: 0xef400000
bttv4: using: IVC-200 [card=102,insmod option]
bttv4: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv4: using tuner=-1
bttv4: i2c: checking for MSP34xx @ 0x80... not found
bttv4: i2c: checking for TDA9875 @ 0xb0... not found
bttv4: i2c: checking for TDA7432 @ 0x8a... not found
bttv4: i2c: checking for TDA9887 @ 0x86... <6>input: PC Speaker as /class/input/input1
bttv4: registered device video4
bttv4: registered device vbi4
bttv4: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (5).
bttv5: Bt878 (rev 17) at 0000:04:0d.0, irq: 11, latency: 64, mmio: 0xef200000
bttv5: using: IVC-200 [card=102,insmod option]
bttv5: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv5: using tuner=-1
bttv5: i2c: checking for MSP34xx @ 0x80... not found
bttv5: i2c: checking for TDA9875 @ 0xb0... not found
bttv5: i2c: checking for TDA7432 @ 0x8a... not found
bttv5: i2c: checking for TDA9887 @ 0x86... not found
bttv5: registered device video5
bttv5: registered device vbi5
bttv5: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (6).
bttv6: Bt878 (rev 17) at 0000:04:0e.0, irq: 10, latency: 64, mmio: 0xef000000
bttv6: using: IVC-200 [card=102,insmod option]
bttv6: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv6: using tuner=-1
bttv6: i2c: checking for MSP34xx @ 0x80... not found
bttv6: i2c: checking for TDA9875 @ 0xb0... not found
bttv6: i2c: checking for TDA7432 @ 0x8a... not found
bttv6: i2c: checking for TDA9887 @ 0x86... not found
bttv6: registered device video6
bttv6: registered device vbi6
bttv6: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (7).
bttv7: Bt878 (rev 17) at 0000:04:0f.0, irq: 3, latency: 64, mmio: 0xeee00000
bttv7: using: IVC-200 [card=102,insmod option]
bttv7: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv7: using tuner=-1
bttv7: i2c: checking for MSP34xx @ 0x80... not found
bttv7: i2c: checking for TDA9875 @ 0xb0... not found
bttv7: i2c: checking for TDA7432 @ 0x8a... not found
bttv7: i2c: checking for TDA9887 @ 0x86... not found
bttv7: registered device video7
bttv7: registered device vbi7
bttv7: PLL: 28636363 => 35468950 .. ok
bttv1: timeout: drop=0 irq=30/90, risc=3763d010, bits: HSYNC
bttv1: reset, reinitialize
bttv1: PLL: 28636363 => 35468950 . ok
bttv0: timeout: drop=0 irq=29/30, risc=376ad000, bits: HSYNC
bttv0: reset, reinitialize
bttv0: PLL: 28636363 => 35468950 . ok
bttv2: timeout: drop=0 irq=32/33, risc=37599000, bits: HSYNC
bttv2: reset, reinitialize
bttv2: PLL: 28636363 => 35468950 . ok
bttv1: timeout: drop=0 irq=34/94, risc=3763d000, bits: VSYNC HSYNC
bttv0: timeout: drop=0 irq=32/52, risc=376ad000, bits: VSYNC HSYNC
bttv4: timeout: drop=0 irq=28/59, risc=37304000, bits: HSYNC
bttv4: reset, reinitialize
bttv4: PLL: 28636363 => 35468950 . ok
bttv2: timeout: drop=0 irq=33/34, risc=37599000, bits: VSYNC HSYNC
bttv5: timeout: drop=0 irq=29/123, risc=36d39000, bits: HSYNC
bttv5: reset, reinitialize
bttv5: PLL: 28636363 => 35468950 . ok
bttv4: timeout: drop=0 irq=31/62, risc=37304000, bits: VSYNC HSYNC
bttv6: timeout: drop=0 irq=29/59, risc=37235000, bits: HSYNC
bttv6: reset, reinitialize
bttv6: PLL: 28636363 => 35468950 . ok
bttv5: timeout: drop=0 irq=32/126, risc=36d39000, bits: VSYNC HSYNC
bttv7: timeout: drop=0 irq=28/37, risc=37705000, bits: HSYNC
bttv7: reset, reinitialize
bttv7: PLL: 28636363 => 35468950 . ok
bttv6: timeout: drop=0 irq=32/62, risc=37235000, bits: VSYNC HSYNC
bttv3: timeout: drop=0 irq=31/62, risc=3708a000, bits: HSYNC
bttv3: reset, reinitialize
bttv3: PLL: 28636363 => 35468950 . ok
bttv7: timeout: drop=0 irq=31/60, risc=37705000, bits: VSYNC HSYNC
bttv3: timeout: drop=0 irq=32/63, risc=3708a000, bits: VSYNC HSYNC
bttv0: reset, reinitialize
bttv0: PLL: 28636363 => 35468950 .<6>bttv2: reset, reinitialize
bttv2: PLL: 28636363 => 35468950 . ok
bttv1: reset, reinitialize
bttv1: PLL: 28636363 => 35468950 . ok
bttv2: timeout: drop=0 irq=34/66, risc=37599000, bits: VSYNC HSYNC
bttv0: timeout: drop=0 irq=35/66, risc=376ad000, bits: VSYNC HSYNC
bttv1: timeout: drop=0 irq=37/172, risc=3763d000, bits: VSYNC HSYNC
bttv4: reset, reinitialize
bttv4: PLL: 28636363 => 35468950 .<6>bttv6: reset, reinitialize
bttv6: PLL: 28636363 => 35468950 . ok
bttv5: reset, reinitialize
bttv5: PLL: 28636363 => 35468950 . ok
bttv4: timeout: drop=0 irq=34/68, risc=37304000, bits: VSYNC HSYNC
bttv5: timeout: drop=0 irq=35/190, risc=36d39000, bits: VSYNC HSYNC
bttv6: timeout: drop=0 irq=35/66, risc=37235000, bits: VSYNC HSYNC
bttv3: reset, reinitialize
bttv3: PLL: 28636363 => 35468950 . ok
bttv7: reset, reinitialize
bttv7: PLL: 28636363 => 35468950 . ok
bttv3: timeout: drop=0 irq=33/67, risc=3708a000, bits: VSYNC HSYNC
bttv7: timeout: drop=0 irq=34/64, risc=37705000, bits: VSYNC HSYNC

For the delay, add this to the options file. The audio is normal as it is in the chip, but usually not implemented.
This is the other line I add for my card. It is a Chinese clone...

hi there, i've tested the suggestion
on /etc/modprobe.d/modprobe.conf

options i2c_algo_bit bit_test=1
options bttv gbuffers=16 radio=-1 tuner=4 card=102,102,102,102,102,102,102,102

and also the combo


options i2c_algo_bit bit_test=1
options bttv gbuffers=16 radio=-1 card=77,77,77,77,77,77,77,77

cause in my last installation this card (a kodicom8800 china-clone) work perfectly
with the 77 settings.

and in both case i never have the "blue screen" only black screen on zoneminder
and also was not able to have a videocapture work (test the kdetv)

i download the last vanilla kernel 2.6.24.2 and try to use it.

the problem continue to damn me...

here is the dmesg when i try to mount on the mod.

-------->modprobe bttv
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:04:08.0, irq: 5, latency: 64, mmio: 0xefc00000
bttv0: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-0: adapter [bt878 #0 [sw]] registered
i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x50
i2c-adapter i2c-0: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-0: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-0: NAK from device addr 0x50 msg #0
bttv0: tuner absent
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (1).
bttv1: Bt878 (rev 17) at 0000:04:09.0, irq: 11, latency: 64, mmio: 0xefa00000
bttv1: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-1: adapter [bt878 #1 [sw]] registered
i2c-adapter i2c-1: found normal entry for adapter 1, addr 0x50
i2c-adapter i2c-1: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-1: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-1: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-1: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-1: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-1: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-1: NAK from device addr 0x50 msg #0
bttv1: tuner absent
bttv1: registered device video1
bttv1: registered device vbi1
bttv1: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (2).
bttv2: Bt878 (rev 17) at 0000:04:0a.0, irq: 10, latency: 64, mmio: 0xef800000
bttv2: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv2: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-2: adapter [bt878 #2 [sw]] registered
i2c-adapter i2c-2: found normal entry for adapter 2, addr 0x50
i2c-adapter i2c-2: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-2: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-2: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-2: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-2: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-2: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-2: NAK from device addr 0x50 msg #0
bttv2: tuner absent
bttv2: registered device video2
bttv2: registered device vbi2
bttv2: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (3).
bttv3: Bt878 (rev 17) at 0000:04:0b.0, irq: 3, latency: 64, mmio: 0xef600000
bttv3: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv3: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-3: adapter [bt878 #3 [sw]] registered
i2c-adapter i2c-3: found normal entry for adapter 3, addr 0x50
i2c-adapter i2c-3: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-3: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-3: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-3: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-3: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-3: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-3: NAK from device addr 0x50 msg #0
bttv3: tuner absent
bttv3: registered device video3
bttv3: registered device vbi3
bttv3: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (4).
bttv4: Bt878 (rev 17) at 0000:04:0c.0, irq: 5, latency: 64, mmio: 0xef400000
bttv4: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv4: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-4: adapter [bt878 #4 [sw]] registered
i2c-adapter i2c-4: found normal entry for adapter 4, addr 0x50
i2c-adapter i2c-4: master_xfer[0] W, addr=0x50, len=0
i2c-adai2c-adapter i2c-4: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-4: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-4: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-4: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-4: NAK from device addr 0x50 msg #0
bttv4: tuner absent
bttv4: registered device video4
bttv4: registered device vbi4
bttv4: PLL: 28636363 => 35468950 . okpter i2c-4: i2c_outb: 0xa0, timeout at bit #7

bttv: Bt8xx card found (5).
bttv5: Bt878 (rev 17) at 0000:04:0d.0, irq: 11, latency: 64, mmio: 0xef200000
bttv5: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv5: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-5: adapter [bt878 #5 [sw]] registered
i2c-adapter i2c-5: found normal entry for adapter 5, addr 0x50
i2c-adapter i2c-5: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-5: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-5: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-5: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-5: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-5: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-5: NAK from device addr 0x50 msg #0
bttv5: tuner absent
bttv5: registered device video5
bttv5: registered device vbi5
bttv5: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (6).
bttv6: Bt878 (rev 17) at 0000:04:0e.0, irq: 10, latency: 64, mmio: 0xef000000
bttv6: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv6: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-6: adapter [bt878 #6 [sw]] registered
i2c-adapter i2c-6: found normal entry for adapter 6, addr 0x50
i2c-adapter i2c-6: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-6: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-6: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-6: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-6: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-6: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-6: NAK from device addr 0x50 msg #0
bttv6: tuner absent
bttv6: registered device video6
bttv6: registered device vbi6
bttv6: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (7).
bttv7: Bt878 (rev 17) at 0000:04:0f.0, irq: 3, latency: 64, mmio: 0xeee00000
bttv7: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv7: gpio: en=00000000, out=00000000 in=00fffff2 [init]
i2c-adapter i2c-7: adapter [bt878 #7 [sw]] registered
i2c-adapter i2c-7: found normal entry for adapter 7, addr 0x50
i2c-adapter i2c-7: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-7: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-7: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-7: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-7: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-7: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-7: NAK from device addr 0x50 msg #0
bttv7: tuner absent
bttv7: registered device video7
bttv7: registered device vbi7
bttv7: PLL: 28636363 => 35468950 . ok


-----------------------------
appear that i've some trouble with the i2c-adapter (at least from what i can understand)
i suffer from a timeout at bit 7 ... what the F#@K is?

ok, the hardware i use is a asus pundit r-350
maybe is a irq issue? (i see that this card use 4 irq and are shared by other device too)

any suggestions is very welcome cause is a real hard fight here .

thanks a lot.

Well let us see your interrrupts

cat /proc/interrupts

root@videoserver:~# cat /proc/interrupts
CPU0
0: 905981 XT-PIC-XT timer
1: 10 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
3: 231 XT-PIC-XT bttv3, bttv7
5: 286 XT-PIC-XT ATI IXP, bttv0, bttv4
8: 1 XT-PIC-XT rtc
9: 1 XT-PIC-XT acpi
10: 249 XT-PIC-XT ehci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3, bttv2, bttv6
11: 824 XT-PIC-XT bttv1, bttv5, eth0
14: 81103 XT-PIC-XT ide0
NMI: 0 Non-maskable interrupts
TRM: 0 Thermal event interrupts
SPU: 0 Spurious interrupts
ERR: 0



using sensors-detect:

i dont put the outcome, cut it and just the summary, but this stay
so looong trying to communicate with capt. card.

[...]

Next adapter: SMBus PIIX4 adapter at 0a00 (i2c-0)
Do you want to scan it? (YES/no/selectively):
Client found at address 0x52
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Success!
(confidence 8, driver `eeprom')

Next adapter: bt878 #0 [sw] (i2c-1)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #1 [sw] (i2c-2)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #2 [sw] (i2c-3)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #3 [sw] (i2c-4)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #4 [sw] (i2c-5)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #5 [sw] (i2c-6)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #6 [sw] (i2c-7)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #7 [sw] (i2c-8)
Do you want to scan it? (YES/no/selectively):
[...]




Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `eeprom' (should be inserted):
Detects correctly:
* Bus `SMBus PIIX4 adapter at 0a00'
Busdriver `i2c-piix4', I2C address 0x52
Chip `SPD EEPROM' (confidence:

EEPROMs are *NOT* sensors! They are data storage chips commonly
found on memory modules (SPD), in monitors (EDID), or in some
laptops, for example.

Driver `it87' (should be inserted):
Detects correctly:
* ISA bus, address 0x260
Chip `ITE IT8712F Super IO Sensors' (confidence: 9)









using lspci -vv -nn




00:00.0 Host bridge [0600]: ATI Technologies Inc Radeon 9100 IGP Host Bridge [1002:7833]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8107]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: Memory at f0000000 (32-bit, prefetchable)
Region 1: Memory at feb00000 (32-bit, non-prefetchable)
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge [0604]: ATI Technologies Inc Radeon 9100 IGP PCI/AGP Bridge [1002:7838] (prog-if 00 [Normal de
code])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdb00000-fdefffff
Prefetchable memory behind bridge: dde00000-eddfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-

00:13.0 USB Controller [0c03]: ATI Technologies Inc OHCI USB Controller #1 [1002:4347] (rev 01) (prog-if 10 [OHCI
])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe800000 (32-bit, non-prefetchable)

00:13.1 USB Controller [0c03]: ATI Technologies Inc OHCI USB Controller #2 [1002:4348] (rev 01) (prog-if 10 [OHCI
])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe900000 (32-bit, non-prefetchable)

00:13.2 USB Controller [0c03]: ATI Technologies Inc EHCI USB Controller [1002:4345] (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fea00000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+

00:14.0 SMBus [0c05]: ATI Technologies Inc SMBus [1002:4353] (rev 18)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 0a00
Region 1: Memory at 40000000 (32-bit, non-prefetchable)

00:14.1 IDE interface [0101]: ATI Technologies Inc Dual Channel Bus Master PCI IDE Controller [1002:4349] (prog-i
f 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort+ <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ff00 [size=16]

00:14.3 ISA bridge [0601]: ATI Technologies Inc Unknown device [1002:434c]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:14.4 PCI bridge [0604]: ATI Technologies Inc Unknown device [1002:4342] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=03, sec-latency=64
Memory behind bridge: fdf00000-fe0fffff
Prefetchable memory behind bridge: ede00000-efdfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

00:14.5 Multimedia audio controller [0401]: ATI Technologies Inc IXP150 AC'97 Audio Controller [1002:4341]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:810d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 5
Region 0: Memory at fe700000 (32-bit, non-prefetchable) [size=256]

01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon 9100 PRO IGP [1002:7834] (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8107]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at d000 [size=256]
Region 2: Memory at fde00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fdd00000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- 64bit+ FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:09.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139 [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at fe000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:0e.0 PCI bridge [0604]: Hint Corp HiNT HB4 PCI-PCI Bridge (PCI6150) [3388:0022] (rev 04) (prog-if 00 [Normal d
ecode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
Prefetchable memory behind bridge: 00000000ede00000-00000000efdfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e4] #06 [0094]
Capabilities: [e8] Vital Product Data

03:08.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at efc00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:08.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at efd00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:09.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at efa00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:09.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at efb00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0a.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ef800000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0a.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ef900000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0b.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 3
Region 0: Memory at ef600000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0b.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 3
Region 0: Memory at ef700000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0c.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ef400000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0c.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ef500000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:0d.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ef200000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0d.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ef300000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0e.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ef000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0e.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ef100000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0f.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 3
Region 0: Memory at eee00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0f.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 3
Region 0: Memory at eef00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-





root@videoserver:/var/log/zm# tail -n20 zmdc.log
02/18/08 10:03:53.081789 zmdc[4012].INF ['zmc -d /dev/v4l/video3' starting at 08/02/18 10:03:53, pid = 4245]
02/18/08 10:03:53.657825 zmdc[4012].ERR ['zmc -d /dev/v4l/video3' exited abnormally, exit status 255]
02/18/08 10:03:55.056221 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video1]
02/18/08 10:03:55.093832 zmdc[4012].INF ['zmc -d /dev/v4l/video1' starting at 08/02/18 10:03:55, pid = 4246]
02/18/08 10:03:55.633624 zmdc[4012].ERR ['zmc -d /dev/v4l/video1' exited abnormally, exit status 255]
02/18/08 10:03:56.032177 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video0]
02/18/08 10:03:56.049730 zmdc[4012].INF ['zmc -d /dev/v4l/video0' starting at 08/02/18 10:03:56, pid = 4247]
02/18/08 10:03:56.050265 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video2]
02/18/08 10:03:56.112455 zmdc[4012].INF ['zmc -d /dev/v4l/video2' starting at 08/02/18 10:03:56, pid = 4248]
02/18/08 10:03:56.681663 zmdc[4012].ERR ['zmc -d /dev/v4l/video0' exited abnormally, exit status 255]
02/18/08 10:03:56.777794 zmdc[4012].ERR ['zmc -d /dev/v4l/video2' exited abnormally, exit status 255]
02/18/08 10:03:58.076204 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video5]
02/18/08 10:03:58.113793 zmdc[4012].INF ['zmc -d /dev/v4l/video5' starting at 08/02/18 10:03:58, pid = 4249]
02/18/08 10:03:58.701812 zmdc[4012].ERR ['zmc -d /dev/v4l/video5' exited abnormally, exit status 255]
02/18/08 10:03:59.000175 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video6]
02/18/08 10:03:59.037817 zmdc[4012].INF ['zmc -d /dev/v4l/video6' starting at 08/02/18 10:03:59, pid = 4250]
02/18/08 10:03:59.625808 zmdc[4012].ERR ['zmc -d /dev/v4l/video6' exited abnormally, exit status 255]
02/18/08 10:04:00.024219 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video7]
02/18/08 10:04:00.061744 zmdc[4012].INF ['zmc -d /dev/v4l/video7' starting at 08/02/18 10:04:00, pid = 4251]
02/18/08 10:04:00.649805 zmdc[4012].ERR ['zmc -d /dev/v4l/video7' exited abnormally, exit status 255]




this help in some manners?