ZoneMinder Forums

Folks,
I have the above LiveCD installed on a dual core machine. When I set up my test camera (this is a test machine) I get the broken page symbol in the image area. The camera is a DLink DCS-910. I have them working (with the caveat seen elsewhere on the list under 1.23.3, and except when the camera gets stopped due to power loss or a change of something on the setup tabs they seem to work just fine. But on my ZMLarch test machine I can not get any video. Here is a chunk out of the zmdc log:
09/20/09 05:29:14.447509 zmdc[3340].INF [Server shutdown at 09/09/20 05:29:14]
09/20/09 05:29:26.401599 zmdc[5054].INF [Server starting at 09/09/20 05:29:26]
09/20/09 05:29:29.523540 zmdc[5054].INF ['zmc -m 1' starting at 09/09/20 05:29:29, pid = 5077]
09/20/09 05:29:29.648464 zmdc[5054].INF ['zmfilter.pl' starting at 09/09/20 05:29:29, pid = 5082]
09/20/09 05:29:29.819859 zmdc[5054].INF ['zmaudit.pl -c' starting at 09/09/20 05:29:29, pid = 5086]
09/20/09 05:29:29.969229 zmdc[5054].INF ['zmwatch.pl' starting at 09/09/20 05:29:29, pid = 5092]
09/20/09 05:29:30.096324 zmdc[5054].INF ['zmupdate.pl -c' starting at 09/09/20 05:29:30, pid = 5096]
09/20/09 05:29:39.578666 zmdc[5054].ERR ['zmc -m 1' exited abnormally, exit status 6]
09/20/09 05:29:39.578913 zmdc[5054].INF [Starting pending process, zmc -m 1]
09/20/09 05:29:39.594706 zmdc[5054].INF ['zmc -m 1' starting at 09/09/20 05:29:39, pid = 5108]
09/20/09 05:29:49.622557 zmdc[5054].ERR ['zmc -m 1' exited abnormally, exit status 6]
09/20/09 05:29:54.031448 zmdc[5054].INF [Starting pending process, zmc -m 1]
09/20/09 05:29:54.032135 zmdc[5054].INF ['zmc -m 1' starting at 09/09/20 05:29:54, pid = 5111]
09/20/09 05:30:04.072121 zmdc[5054].ERR ['zmc -m 1' exited abnormally, exit status 6]
09/20/09 05:30:14.091928 zmdc[5054].INF [Starting pending process, zmc -m 1]
09/20/09 05:30:14.092691 zmdc[5054].INF ['zmc -m 1' starting at 09/09/20 05:30:14, pid = 5117]
09/20/09 05:30:24.130970 zmdc[5054].ERR ['zmc -m 1' exited abnormally, exit status 6]

I am trying to poke at this and get it fixed, as I understand that 1.24 will operate with these cameras just fine. I have done several searches on the error and come up empty handed, perhaps I needed to enter it as some other form of error?

If any of you want to look at 2 of the cameras operating, you can go to:
www.wchast.com/zm
user = guest
pass = guest
The cameras named 'gate' and 'dock' are dcs-910's. For some strange reason the one on the dock will drop out at night at times but the other one works just fine. FYI the cam named 'driveway' is a TrendNET IP-TV110 and the one called 'front_door' is a old DCS-1000W.

I have tested them at both 320X240 and 640X480 making sure that all of the settings were correct. I can get a image stream out of both /video.cgi? and /mjpeg.cgi with my web browser.

Oh yes I also noticed that on the console screen there is no ID nor is the cycle/montage selector visible. I went to add a second cam and the linked monitor comes up with the name of the first cam in there so I did not proceed with that test as I could not get rid of the linked monitory.

Folks

I need some advice about the config of the cameras TV-IP110. I went through all possible post and was poeking with the downgrade of the firmeware however the ZM still show the errors.
zmc_m1[27868]: ERR [Unrecognised content type 'multipart/mixed']
zmc_m1[27868]: ERR [Unable to get response]
zmc_m1[27868]: ERR [Failed to capture image from monitor 1 (0/1)]
zmdc[27816]: ERR ['zmc -m 1' exited abnormally, exit status 255]

Second Axis camera is perfectly connected. Is there any magic about the setings?

PPyszk

It's all FM. Post your source->source settings and someone will help out.