ZoneMinder Forums

Hi,

I am adding a new camera my system, I currently have 4 ycam blacks which work fine under ZM.

The new camera is a CNB IVP4030VR, I can get video showing in VLC by using the following URLs' there are two feeds one H.264 and MJPG - see codec info from vlc

rtsp://root:admin@192.168.128.21:554

Codec: H264 - MPEG-4 AVC (part 10) (h264)
Resolution: 640x480
Decoded format: Planar 4:2:0 YUV

rtsp://root:admin@192.168.128.21:665
Codec: Motion JPEG Video (MJPG)
Resolution: 640x480
Decoded format: Planar 4:2:0 YUV full scale

I have tried all four rtsp options and they all get error messages listed below

using url of rtsp://root:admin@192.168.128.21:554

RTP Unicast

Jan 22 12:39:15 video-server zmc_m5[18707]: INF [Starting Capture]
Jan 22 12:39:16 video-server zmc_m5[18707]: FAT [Unable to get RTP Info identifier from response 'RTSP/1.0 200 OK#015#012CSeq: 3#015#012Session: 1923148594#015#012#015#012']

RTP Multicast

Jan 22 12:40:11 video-server zmc_m5[18796]: INF [Starting Capture]
Jan 22 12:40:12 video-server zmc_m5[18796]: FAT [Unable to get RTP Info identifier from response 'RTSP/1.0 200 OK#015#012CSeq: 3#015#012Session: 265978491#015#012#015#012']

RTP/RTSP

Jan 22 12:51:22 video-server zmc_m6[19327]: FAT [No RTSP sources]


RTP/RTSP/HTTP

an 22 12:43:15 video-server zmc_m5[18910]: FAT [No RTSP sources]

using url of rtsp://root:admin@192.168.128.21:665

RTP Unicast

Jan 22 12:48:50 video-server zmc_m6[19113]: FAT [Unable to get RTP Info identifier from response 'RTSP/1.0 200 OK#015#012CSeq: 3#015#012Session: 235454179#015#012#015#012']


RTP Multicast

Jan 22 12:49:13 video-server zmc_m6[19152]: FAT [Unable to get RTP Info identifier from response 'RTSP/1.0 200 OK#015#012CSeq: 3#015#012Session: 300155902#015#012#015#012']

RTP/RTSP

Jan 22 12:50:02 video-server zmc_m6[19214]: FAT [No RTSP sources]


RTP/RTSP/HTTP

Jan 22 12:50:44 video-server zmc_m6[19268]: FAT [No RTSP sources]


I have also tried using ffmpeg and it just says

Jan 22 13:04:01 video-server zmc_m7[19836]: INF [Priming capture from rtsp://root:admin@192.168.128.21:655]
Jan 22 13:04:01 video-server zmc_m7[19836]: FAT [Unable to open input rtsp://root:admin@192.168.128.21:655 due to: Operation now in progress]

any ideas?

cheers
Toby

If its any consolation I have a RTSP problem also and like you it works just fine in VLC using the URL rtsp://192.168.1.11:554/live.sdp
VLC reports the media as :

Codec : Motion JPEG Video
Resolution : 640x480
Decoded Format : Planar 4:2:0 YUV Full Scale

The log is full of the same errors :

2013-01-31 22:16:24.704962
zmc_m1 3441 ERR
256: 00 00 00 00 01 80 50 3c 00 00 00 80 06 04 05 06 05 04 06 06 05 06 07 07 06 08 0a 10 0a 0a 09 09 0a 14 0e 0f 0c 10 17 14 18 18 17 14 16 16 1a 1d 25 1f 1a 1b 23 1c 16 16 20 2c 20 23 26 27 29 2a 29 19 1f 2d 30 2d 28 30 25 28 29 28 07 07 07 0a 08 0a 13 0 zm_remote_camera_rtsp.cpp 225

2013-01-31 22:16:24.697323 zmc_m1 3441 ERR
Error while decoding frame 0 zm_remote_camera_rtsp.cpp 224

Tried various formats etc but no success....

My Camera is a Cisco VC220

Punyelroo

http://www.zoneminder.com/forums/viewto ... peg#p78880

See if this gives you any ideas. (Source FFMpeg)

thanks will try them, only just realised I was not subscribed to this topic otherwise would have replied earlier!

cheers

no unforunately that does not work either, is there any paid support for adding new cameras as will need to buy new cameras if this does not work!

thanks

I would say good luck with getting RTSP working, or getting paid support.

I am in very much the same boat as you, and I even put up a "Paid Support" post, and not one reply.

And talking of boat's I can see you are just a stone's throw away from my little island.

Here is my Post: Any Paid Support for ZoneMinder?

I hope you have better luck then I did.

Best Regards.