Hikvision Control Settings

[iamnotme]

Hello,

After battling my own ineptitude and getting Hikvision PTZ control working, and also tackling Multiport, I am now trying to get the camera movement working properly.

I have set auto stop to 1s as a single click was causing the camera to PAN for 10s, rather than stop once I let go. The problem now is that if hold a PAN control it just moves for 1s and I get a 403 Forbidden in the event log from the camera.

This is an extract from the capabilities xml:

Code: Select all

<AbsolutePanTiltPositionSpace>
<XRange>
<Min>0</Min>
<Max>3600</Max>
</XRange>
<YRange>
<Min>-221</Min>
<Max>828</Max>
</YRange>
</AbsolutePanTiltPositionSpace>
<AbsoluteZoomPositionSpace>
<ZRange>
<Min>10</Min>
<Max>250</Max>
</ZRange>
</AbsoluteZoomPositionSpace>
<ContinuousPanTiltSpace>
<XRange>
<Min>-100</Min>
<Max>100</Max>
</XRange>
<YRange>
<Min>-100</Min>
<Max>100</Max>
</YRange>
</ContinuousPanTiltSpace>
<ContinuousZoomSpace>
<ZRange>
<Min>-100</Min>
<Max>100</Max>
</ZRange>

This is the capture for the commands:

Code: Select all

No.	Time	Source	Destination	Protocol	Length	Info
3399	13.819273	10.2.1.27	10.2.1.11	HTTP	710	PUT /ISAPI/PTZCtrl/channels/1/momentary HTTP/1.1  (application/x-www-form-urlencoded)
3409	13.820930	10.2.1.11	10.2.1.27	TCP	72	80 → 46702 [ACK] Seq=1 Ack=639 Win=30240 Len=0 TSval=527616014 TSecr=492008879
3410	13.826222	10.2.1.11	10.2.1.27	HTTP/XML	584	HTTP/1.1 200 OK 
3411	13.826222	10.2.1.11	10.2.1.27	TCP	72	80 → 46702 [FIN, ACK] Seq=513 Ack=639 Win=30240 Len=0 TSval=527616014 TSecr=492008879
3412	13.826259	10.2.1.27	10.2.1.11	TCP	72	46702 → 80 [ACK] Seq=639 Ack=513 Win=64128 Len=0 TSval=492008886 TSecr=527616014
3413	13.827540	10.2.1.27	10.2.1.11	TCP	72	46702 → 80 [FIN, ACK] Seq=639 Ack=514 Win=64128 Len=0 TSval=492008888 TSecr=527616014
3414	13.829359	10.2.1.11	10.2.1.27	TCP	72	80 → 46702 [ACK] Seq=514 Ack=640 Win=30240 Len=0 TSval=527616014 TSecr=492008888
3727	14.878948	10.2.1.27	10.2.1.11	TCP	80	46716 → 80 [SYN] Seq=0 Win=64240 Len=0 MSS=1460 SACK_PERM TSval=492009939 TSecr=0 WS=128
3728	14.881363	10.2.1.11	10.2.1.27	TCP	80	80 → 46716 [SYN, ACK] Seq=0 Ack=1 Win=28960 Len=0 MSS=1460 SACK_PERM TSval=527616120 TSecr=492009939 WS=32
3729	14.881422	10.2.1.27	10.2.1.11	TCP	72	46716 → 80 [ACK] Seq=1 Ack=1 Win=64256 Len=0 TSval=492009941 TSecr=527616120
3730	14.881835	10.2.1.27	10.2.1.11	HTTP	650	PUT /ISAPI/PTZCtrl/channels/1/continuous HTTP/1.1  (application/x-www-form-urlencoded)
3731	14.885057	10.2.1.11	10.2.1.27	TCP	72	80 → 46716 [ACK] Seq=1 Ack=579 Win=30144 Len=0 TSval=527616120 TSecr=492009942
3732	14.888651	10.2.1.11	10.2.1.27	HTTP/XML	624	HTTP/1.1 403 Forbidden 

Also attached is a picture of my PAN settings. Has anyone managed to get continuous PAN working on Hikvision?

[iamnotme]

Resolved this by setting the auto stop to 0 although I am sure I tried this previously.

[blaczero]

Can you post your control settings?

I have a hikvision I just bought from amazon and cannot even get control working, but I do see the camera image.